• #maker+t=market
  • 3D列印服務
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Mitchell King
2019-07-20 04:42:41

I posted a couple weeks ago showing my dual Photon setup on the toolbox. Got quite a few likes. Sweet! Now if likes made money....

I have 2 idle Photons. Does anyone have any suggestions of things to start printing that will actually sell? I primarily operate online through my own website and Etsy.

翻譯年糕

Keith Barnett
2019-07-20 05:06:06

Mitchell King
2019-07-20 05:08:04

Max Dercum
2019-07-20 06:58:21

Mitchell King
2019-07-20 06:59:00

Max Dercum
2019-07-20 06:59:51

Mitchell King
2019-07-20 07:01:10

阮天青
2019-07-20 08:48:57

Mitchell King
2019-07-20 08:50:14

Scott Pavlich
2019-07-20 09:07:58

Mitchell King
2019-07-20 09:11:13

Scott Pavlich
2019-07-20 09:18:28

Mitchell King
2019-07-20 09:23:49

Susan Sioux Mercer
2019-07-20 09:25:02

Scott Pavlich
2019-07-20 10:07:51

Ali Reza M
2019-07-20 10:16:32


原文網址 Mitchell King
2019-07-04 06:55:16

27" husky toolbox + butcher block top. Out the door from Home Depot for under $100. Drawer for the tools, cabinet holds the resin, cleaning station, and the curing box.

翻譯年糕

Jeremy Lauzon
2019-07-04 07:01:34

Mitchell King
2019-07-04 07:02:20

Jarrod Smith
2019-07-04 07:19:57

Tom Ligman
2019-07-04 07:23:21

Mitchell King
2019-07-04 07:25:02

Mitchell King
2019-07-04 07:25:15

Tom Ligman
2019-07-04 07:31:50

Alex Po Iorgulescu
2019-07-04 07:40:06

Brent Sinclair
2019-07-04 07:40:27

Rick Garza
2019-07-04 07:45:25

Jeremy Lauzon
2019-07-04 08:06:41

Mitchell King
2019-07-04 08:20:50

Mitchell King
2019-07-04 08:26:51

Matt Goody Goodrich
2019-07-04 10:40:05

Warren Cooper
2019-07-04 12:12:37

Róbert Taller
2019-07-04 17:17:45

Mitchell King
2019-07-04 21:12:33

Warren Cooper
2019-07-04 21:24:27


原文網址 Mitchell King
2019-04-18 02:12:53

New to the photon. What would cause a failure like this where it split from supports? Only 2 on that end, not the third nor anywhere else.

翻譯年糕

Greg Jones
2019-04-18 02:17:44

Doug Vine
2019-04-18 02:17:56

Mitchell King
2019-04-18 02:20:41

Christian Plösser
2019-04-18 03:10:41

Dennis Back
2019-04-19 02:39:08

Mitchell King
2019-04-19 02:50:03

Dennis Back
2019-04-19 02:58:24

Saïmone Goblet
2019-04-20 13:53:34


原文網址 Mitchell King
2019-04-14 05:00:04

TL;DR - Anycubic sent broken printer, looking for troubleshooting tips on not powering on.

Ordered a photon from Aliexpress, tried to cancel 2 days into 5 day processing. They said they couldn't, then shipped it. It showed up the same day as the one I ordered from Amazon. Showed up very blatantly used and abused, in non-factory packaging. I opened a dispute and their immediate message was asking me to remove the dispute. (lol)

I decided to take a closer look at how bad this printer was they sent me pre-owned, and I can't even get it to power on at all to inspect the LCD. I've swapped power supplies (which are also different) between the good and the bad, with no change to power.

Is there any quick/simple troubleshooting to this power problem? I'm just looking for a very detailed complaint against the official Anycubic Aliexpress store sending me a used, damaged, non-working printer at $10 more than the NIB I got from amazon.

翻譯年糕

Kevin Rank
2019-04-14 05:25:08

Mitchell King
2019-04-14 05:32:31

Kaile Riser
2019-04-14 06:30:31

Mitchell King
2019-04-14 06:33:22

Kaile Riser
2019-04-14 06:36:13

Mitchell King
2019-04-14 06:40:45

Patrick Nixon
2019-04-14 09:41:27

Mitchell King
2019-04-14 09:56:37

Mitchell King
2019-04-16 10:39:26

Sen Kun
2019-04-16 11:05:13


 

討論主題

全不選 常用關鍵字