Anycubic Photon Printer Owners 造訪社團 » 用戶發文

I have a question,

I had a print issue the other day on my Photon, and someone recommended upgrading to the newest Firmware.

I'm always leary of upgrading in the event that all of my settings would need changed or I F' something up and it bricks my printer...

is there anyone with a good amount of knowledge that could tell me, Should I upgrade my firmware?

I still ahve the original firmware shipped with the printer about a year ago.

IF SO? how do you upgrade firmware?

P.S.

YES, I have searched the group, but I'm finding answers saying one thing,, then other answers saying another, and nothing specific to what I'm wondering.

I don't ask questions often, so I'll say in advance,, YES I know how google works, and I know how to search a forum, I'm asking because I didn't find the answer.

翻譯年糕

Well... that ones weird.

Trying to print the three storms from Big Trouble in Little China..

Dont quite know what happened?

I'm going to chalk it up to a slicer error, or a fluke and try again....

The last pic is the one that printed.... ok?

Weird..

翻譯年糕

Asking for some assistance with a new Resin.

because of a lot of recommendations on this forum, I ordered some Siraya Blue Resin that should arrive today. Don't get me wrong, the Ancycubic green was working fine, but I had multiple people say that the Siraya was a little stronger and less prone to breaking.

I am still using the STOCK Photon Slicer.

Can I use the Same settings as Anycubic Green? or if not, does anyone have some recommended settings for Siraya Blue Resin?

I print D&D miniatures, if that makes a difference.

翻譯年糕

I need some assistance with ChiTuBox settings.

I installed the new version of ChiTuBox. I'll be honest, I had no issues with the old photon slicer except it did not work on my laptop, and the new ChiTuBox does!!!

BUT...

I used the default settings for the Photon, call it luck, call it using any cubic green and monocure gunmetal grey.. but the stock .05 settings worked great on everything.

The terminology under settings is a bit different now.

I am just wondering what the stock anycubic settings should be in the new software?

here are the settings i used before. (.05) and the options ChiTuBox gives.

what is "light off delay" and "bottom Light off delay" ????

should they both be 1 to match the original software? or are they something different?

翻譯年糕

Hey guys, anyone have any idea what would cause the problem in this picture? I printed three Miniatures all at the same time. But one of them has a flaw her left arm printed completely flat. Any ideas how to minimize the risk of this happening or what would have happened?

翻譯年糕

question for the programmers....

ChiTu is the company that makes the software for the Anycubic.

is the standard slicer they make the same? As in, I realize that the photon slicer adds ".photon" to the end of the file.

but is it really the same file with just the extension changed?

as, in,, could you use the stock ChiTu slicer and just rename the file extension to ".photon" ?????

or are they really making a whole different format file?

翻譯年糕

are there two different models of the Anycubic Photon?

here is why I ask.

I might be remembering this wrong. but I swear my first Photon the Z rod was attached to a block at the top.

my new photon that arrived today, the z rod goes up and just stops in mid air.

maybe i'm confused and imaging things.. but I swear my first one had a block at the top of the z rod that the z rod went into.

翻譯年糕

Well well the new printer arrived. I got everything installed and the bed plate level. Everything appears to be okay all of the screws or tighten down really well. I went ahead and load it up its first print. To immediate things I noticed. The bed is quieter when running up and down the Z screw. And when the bed pulls up off the fep, now it makes more of a crisp cracking sound, rather than before it almost made a dull thud like a drum. I guess after work we'll see if it makes a difference and prints better

翻譯年糕

I'm thinking I might have to return my Anycubic.

I keep seeing all of these large flawless prints.... and mine is still having issues with what looks like "layer lines" at random heights.

looking online it appears it's probably a Z wobble..

I don't feel I should have to tear the whole printer down to it's bare bones and repair it, and risk breaking it, while it's still returnable.........

Hopefully they will send me a replacement as an option.

翻譯年糕

Well after being the guy that says "i dont smell anything from the resin" I ran the whole bottle of anycubic green that came with te printer through. Maybe a faint smell..maybe.

I put some monocure rapid gunmetal grey in today........

Yep... now i can smell it!!! My rooms 2300 square foot and you know the printers running!!

翻譯年糕