• COSPLAY 3D 建模
  • 3D列印服務
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Daniel White
2019-05-06 10:20:42

Any ideas on how to improve the bottom corners on this print. The tops aren't great either but I expect that the bottom warping is affecting the whole print. Monocure blue, 60 second bottom, 10 sec normal.

翻譯年糕

Dennis Back
2019-05-06 10:22:40

Daniel White
2019-05-06 11:25:55

Daniel White
2019-05-06 11:26:24

Dennis Back
2019-05-06 11:37:04

Dennis Back
2019-05-06 11:37:51

Dennis Back
2019-05-06 11:41:50

Dennis Back
2019-05-06 11:46:38

Ken Long
2019-05-06 11:47:39

Daniel White
2019-05-06 12:08:37

Daniel White
2019-05-06 12:10:08

Dennis Back
2019-05-06 12:14:13

Dennis Back
2019-05-06 12:15:26

Daniel White
2019-05-06 12:40:36

Ethan Brown
2019-05-06 12:42:22

Dennis Back
2019-05-06 15:34:03

David McGyver
2019-05-06 19:35:45

Daniel White
2019-05-06 20:04:56

Daniel White
2019-05-06 20:05:21

Johnny Wee
2019-05-06 20:16:23

Johnny Wee
2019-05-06 20:17:25


原文網址 Daniel White
2019-05-04 20:15:05

Tried printing vertically with supports. Anything I print with supports looks crappy. I ended up printing this one direct to the bed and it looks amazing. The images attached are both the crappy one and the good one. The first two are the good ones obviously. Is it possible to print with supports without it looking crap?

翻譯年糕

Dylan Trinh
2019-05-04 20:21:15

Tamás Lehoczky
2019-05-04 20:22:55

Dan Smith
2019-05-04 20:27:00

Dan Smith
2019-05-04 20:29:25

René Hu
2019-05-04 22:03:23

Anthony Pham
2019-05-05 00:28:14

Nick Williams
2019-05-05 02:31:59

Richard Shapiro
2019-05-05 03:34:37

Justin Andrews
2019-05-05 03:46:14

Daniel White
2019-05-05 08:23:48

Ian Robinson
2019-05-08 02:51:52

Daniel White
2019-05-08 04:37:37


原文網址 Daniel White
2019-05-03 06:22:52

All of my prints are coming out too big. An xyz calibration print should be 50, 30 and 8. But it's printing at 50.2, 30.2 and 8.2. that is way too innacurate. The other people printing with fdm's are getting 50.02. I've tried many different exposure times.

Someone mentioned the formware slicer can adjust the size of the image to suit? Is that my only option. If so what is the specific setting in formware called?

翻譯年糕

Nathan Rich
2019-05-03 06:35:17

Tom Franco
2019-05-03 06:52:47

Elvin Torok
2019-05-03 07:02:11

Daniel White
2019-05-03 07:09:32

Daniel White
2019-05-03 07:11:42

Nathan Rich
2019-05-03 09:16:17

Daniel White
2019-05-03 10:04:00

Daniel White
2019-05-03 15:16:34

Daniel White
2019-05-15 16:23:44


原文網址 Daniel White
2019-04-26 16:09:19

What do you think caused this? There's some extra cured resin inside this nut. The bolt doesn't seem to have been affected.

翻譯年糕

Maik Nolte
2019-04-26 16:17:12

Daniel White
2019-04-26 16:40:01

Sean Poeschl
2019-04-26 20:24:50

Sean Poeschl
2019-04-26 20:25:58

Daniel White
2019-04-26 20:26:51

Sean Poeschl
2019-04-26 20:29:55


原文網址 Daniel White
2019-04-26 10:00:23

Is there a way to calibrate the size of the image? I printed a calibration xyz test and it comes out slightly bigger than expected. I also did a nut and bolt test and the nut wont fit on the bolt. I thought this would just be 100% accurate.

翻譯年糕

Stefan Giudici
2019-04-26 10:10:37

Daniel White
2019-04-26 10:11:35

Daniel White
2019-04-26 10:18:15

Scott Clark
2019-04-26 10:19:04

Daniel White
2019-04-26 10:20:54

Todd Jones
2019-04-26 10:26:35

Scott Clark
2019-04-26 10:26:45

Daniel White
2019-04-26 10:27:09

Scott Clark
2019-04-26 10:34:38

Scott Clark
2019-04-26 10:37:31

Robert Silvers
2019-04-26 10:41:39

Scott Clark
2019-04-26 10:45:22

Scott Clark
2019-04-26 10:46:09

Robert Silvers
2019-04-26 10:46:49

Daniel White
2019-04-26 10:53:48

Robert Silvers
2019-04-26 10:54:40

Scott Clark
2019-04-26 10:55:14

Scott Clark
2019-04-26 10:55:58

Daniel White
2019-04-26 10:56:37

Scott Clark
2019-04-26 10:57:37

Scott Clark
2019-04-26 11:00:57

Scott Clark
2019-04-26 11:02:06

Robert Silvers
2019-04-26 11:03:08

Scott Clark
2019-04-26 11:18:33

Jose Elizondo
2019-05-15 07:12:20


 

討論主題

全不選 常用關鍵字