• 3D列印服務
  • COSPLAY 3D 建模
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Eddie Gonzales
2019-12-08 08:37:41

There are days when I get frustrated with the Photon either cause my supports failed or some weird issue with the printer that I can't figure out. Then I print some pre-supported models and the Photon totally redeems itself ? . I wish there were more pre-supported models out there.

翻譯年糕

Brian J Anderson
2019-12-08 08:41:34

Jake Walker
2019-12-08 08:43:56

Jake Walker
2019-12-08 08:44:19

Paul West
2019-12-08 09:58:23

Warren Peace
2019-12-08 10:08:41

Eddie Gonzales
2019-12-08 12:18:27

Khristian Sutherland
2019-12-08 14:30:30

Paul West
2019-12-08 14:33:55

Khristian Sutherland
2019-12-08 14:34:38


原文網址 Eddie Gonzales
2019-09-08 22:39:22

Got my print/support issue solved! I changed my FEP, used the Photon print validator, and installed the fancy new more stable rail by Jackson Products. I think the results speak for themselves. Thanks again for the suggestions and help!

翻譯年糕

Dave Smith
2019-09-08 22:45:09

Michael Horn
2019-09-08 23:33:47

James Ogre Tate
2019-09-08 23:44:51

Eddie Gonzales
2019-09-09 01:00:39

Eddie Gonzales
2019-09-09 01:20:40

Joe Harter
2019-09-09 06:07:40

Luke Mason
2019-09-09 13:12:47

Britt Johnson
2019-09-10 03:24:33


原文網址 Eddie Gonzales
2019-09-02 00:32:40

Hey Everyone,

I was wondering if you all can help me troubleshoot this. I started printing in Elegoo grey resin. I checked the chart and went with the settings below in Chitubox. The weird part was the first print was all screwed up. It wasn't even aligned correctly. I re-leveled and tried again and the 2nd print I did 2 of the same robots and one had a misprint on the left arm and the other had a misprint on the right arm so I think my supports are ok. Could it be a plate alignment issue or is it a Chitubox slicing error? Thanks for your help.

Edit: added Support Screenshots in Chitubox

翻譯年糕

Bronson Ferri
2019-09-02 00:34:32

Paul West
2019-09-02 00:36:56

Chris Baker
2019-09-02 00:37:54

James Ogre Tate
2019-09-02 00:41:37

Chad Elstad
2019-09-02 00:44:28

Eddie Gonzales
2019-09-02 00:50:19

Eddie Gonzales
2019-09-02 00:52:16

Greg Kourakos
2019-09-02 01:40:07

Michael Horn
2019-09-02 09:05:16

James Ogre Tate
2019-09-02 11:03:59


原文網址 Eddie Gonzales
2019-07-31 20:48:35

Second 3D print. Went for something a bit more challenging. This printer is pretty awesome! There was a minor mis-print on one miniature. I probably have to adjust my supports a bit but overall satisfied.

翻譯年糕

Azam Idris
2019-07-31 20:53:10

Eddie Gonzales
2019-08-01 01:04:05

Azam Idris
2019-08-01 06:54:58


原文網址 Eddie Gonzales
2019-07-30 00:04:25

Just finished my first successful print last night. The first cube attempt failed but I searched through this group and watched some YouTube videos, re-leveled the plate, tightened the FEP and re-attempted to print the cube and got a nice print. Thank you for being a helpful community. I jumped the gun and made the Photon my first 3D printer. No prior experience printing. This was pretty much out of the box using the cube file and the stock firmware. Should I consider upgrading the firmware before slicing and printing my next 3D prints?

翻譯年糕

Daniel D'Intino
2019-07-30 00:06:20

Joshua Collins
2019-07-30 00:19:59

Mark Wardle
2019-07-30 01:05:42


 

討論主題

全不選 常用關鍵字