Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Teek Cooper
2019-08-16 16:41:29

So this was a painful, tiny fault that I didn't pick up until after 2 prints had failed to adhere to the build plate. Chitubox support had pushed through the skate and ended up raising the base 4 layers.

翻譯年糕

Anh Hoàng
2019-08-16 16:51:37

Anh Hoàng
2019-08-16 16:52:12

Teek Cooper
2019-08-16 16:52:21

David Bieganek
2019-08-16 17:15:19

Arnie Locsin
2019-08-16 17:47:53

Johannes Weis
2019-08-16 17:50:15

Teek Cooper
2019-08-16 17:52:46

Johannes Weis
2019-08-16 17:54:50

Adam Horton
2019-08-17 03:45:18

原文網址 Teek Cooper
2019-08-13 12:34:04

Just switched to Monocure Rapid Grey and my first print came out with these thin almost gelatinous planes of resin . Is this just under-exposed? Also had cure resin attached to FEP. Using Photon S

翻譯年糕

Joey Smith
2019-08-13 12:36:31

Stephen Farrell
2019-08-13 12:46:06

Paul West
2019-08-13 12:57:24

Seona van der Pol
2019-08-13 13:20:14

Seona van der Pol
2019-08-13 13:21:01

Teek Cooper
2019-08-13 13:22:09

Teek Cooper
2019-08-13 13:22:39

Seona van der Pol
2019-08-13 13:28:27

Scott Pavlich
2019-08-13 13:43:48

Sam Ellis
2019-08-13 14:19:49

Jeff Johnson
2019-08-13 21:48:11

原文網址 Teek Cooper
2019-08-10 12:01:02

Do any Australians have a reliable source for Elegoo Resin. Trying to test a few varieties but can seem to get hold of it.

翻譯年糕

Robert Sakaluk
2019-08-10 12:11:28

Robert Sakaluk
2019-08-10 12:12:48

Teek Cooper
2019-08-10 12:39:08

Greg Chapman
2019-08-10 12:45:04

Teek Cooper
2019-08-10 12:52:26

Greg Chapman
2019-08-10 13:03:09

Billy Thiex
2019-08-11 03:06:32

原文網址 Teek Cooper
2019-08-08 21:46:03

Is anybody else having trouble with the Photon File Validator. I can't seem to get it to read my sliced file.

翻譯年糕

Bob Deblier
2019-08-08 21:59:31

Teek Cooper
2019-08-08 22:00:57

Teek Cooper
2019-08-08 22:01:09

Teek Cooper
2019-08-08 22:33:07

原文網址 Teek Cooper
2019-08-08 09:39:24

Hi guys.

I'm hoping to get some advice as far as supports go. I started this print. Failed because I missed my alarm to add more resin...

I did still pull the print and clean it up just to learn from it. Clipping that many supports was painful. I just used chitubox support defaults.

Could a print this large have succeeded with less supports?

Also I went with hollowing to 3mm walls. The print that came out is extremely sturdy. Would you have gone with thinner walls?

I am thinking for the next attempt that I will cut each piece in half horizontally so that I can have the majority of supports on the flat faces.

Only my third print but I am amazed at the quality I'm getting from this printer.

翻譯年糕

Teek Cooper
2019-08-08 09:40:52

Teek Cooper
2019-08-08 09:41:09

Teek Cooper
2019-08-08 09:41:27

Jeff Johnson
2019-08-09 01:31:10

原文網址 Teek Cooper
2019-08-06 09:54:11

Hey guys. Just got my Photon S. Trying to run the test print but the sliced file is not showing up on the print menu. I don't have an option to select .photons specific file when saving. Any ideas?

翻譯年糕