Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Ray A. Smith Jr.
2019-12-19 10:32:43

Anyone have any idea what could be causing this?

翻譯年糕

Walter Urbanczyk
2019-12-19 10:37:37

Martin Philip Lammers
2019-12-19 10:38:12

Ray A. Smith Jr.
2019-12-19 10:39:27

Martin Philip Lammers
2019-12-19 10:40:08

Justin Coles
2019-12-19 10:45:47

Ray A. Smith Jr.
2019-12-19 10:47:13

Will Koehler
2019-12-19 10:47:32

Ray A. Smith Jr.
2019-12-19 10:48:06

John Hernandez
2019-12-19 10:49:35

Martin Philip Lammers
2019-12-19 10:50:33

Ray A. Smith Jr.
2019-12-19 10:51:42

Ray A. Smith Jr.
2019-12-19 10:52:03

Ray A. Smith Jr.
2019-12-19 10:52:14

Martin Philip Lammers
2019-12-19 10:52:35

Martin Philip Lammers
2019-12-19 10:55:20

Dai Buckley Oam
2019-12-19 10:55:44

Sydnee Davidson
2019-12-19 11:08:06

Sydnee Davidson
2019-12-19 11:10:07

Will Koehler
2019-12-19 11:18:14

Ray A. Smith Jr.
2019-12-19 11:37:23

Will Koehler
2019-12-19 11:39:26

Ray A. Smith Jr.
2019-12-19 11:40:33

Will Koehler
2019-12-19 11:43:15

Ray A. Smith Jr.
2019-12-19 11:43:51

Will Koehler
2019-12-19 11:45:55

Brian T Patterson
2019-12-19 12:01:09

Haydn Nelms
2019-12-19 22:54:42

Ali Al-Qrimli
2019-12-20 04:50:38

Martin Philip Lammers
2019-12-20 06:15:19

原文網址 Ray A. Smith Jr.
2019-12-04 21:54:13

Another question anyone have any lines on a way to set a Photon up with a wifi connections? perhaps using the existing usb?

翻譯年糕

Fred Bey
2019-12-04 22:16:21

Ray A. Smith Jr.
2019-12-04 22:18:31

Fred Bey
2019-12-04 22:19:15

原文網址 Ray A. Smith Jr.
2019-12-04 21:53:20

Holla guys been going strong for a couple of months now and I am hitting on a new issue, proper disposal of the empty resin containers. I have been holding onto them because I know they are toxic does anyone know of the proper way to dispose of these?

翻譯年糕

Juan Pablo Bagnon
2019-12-04 21:56:03

Doug Bowman
2019-12-04 21:56:23

Paul Willsher
2019-12-04 22:00:00

Michael Aaron Carroll
2019-12-04 22:15:36

Jeremy Babcock
2019-12-05 00:22:22

原文網址 Ray A. Smith Jr.
2019-10-14 11:41:07

Has anyone ever used this resin? I am having trouble getting it tuned in. https://www.3dresinsolutions.com/products/hero-resin-dlp-lcd-printing-on-uniz-anycubic-elegoo 翻譯年糕

Nathaniel Red Weidner
2019-10-14 12:16:32

Ray A. Smith Jr.
2019-10-15 01:07:30

Ray A. Smith Jr.
2019-10-15 01:09:56

原文網址 Ray A. Smith Jr.
2019-10-02 04:15:55

so I have blown thru my first to films for my photon in less than 60 prints. Anyone have any recommendations for either a better film or am I just too rough? Oh and the spatula that came with it is trashed misprints that leave a layer attached to the film usually leave them HEAVILY attached and it take some work to get them off. Any recommendations?

翻譯年糕

Scott Pavlich
2019-10-02 04:20:11

Tom Inglis
2019-10-02 04:20:47

Ray A. Smith Jr.
2019-10-02 04:54:10

Ray A. Smith Jr.
2019-10-02 04:54:19

Tom Inglis
2019-10-02 04:55:00

Scott Pavlich
2019-10-02 05:17:18

Melecio Guzman
2019-10-02 12:28:06

原文網址 Ray A. Smith Jr.
2019-09-13 00:40:45

Question, I am new to printing and having a blast but now I am having an issue. How long do you go between changing out your isylpropyl bath and what do you do with the waste alcohol?

翻譯年糕

Evan Boone
2019-09-13 00:45:41

Ray A. Smith Jr.
2019-09-13 00:52:50

原文網址 Ray A. Smith Jr.
2019-09-03 01:57:26

So I had some prints that had small errors, like a monk that had a staff on his back it did not print the lower part of the staff below his waist and the leg that was bent up against his butt. I had a dragon/humanoid mini (Dragonborn) that failed to print its tail. They were both printed completely vertically because they had a base but I read that I should try printing them at angles that may help anyone else tried this and what were the results?

翻譯年糕

Chris Rees
2019-09-03 02:00:38

Ray A. Smith Jr.
2019-09-03 04:40:31

Chris Rees
2019-09-03 05:27:59

原文網址 Ray A. Smith Jr.
2019-08-31 03:48:42

Just got my photon and have tried the test print twice but have not gotten a print to stick to the plate yet. I leveled it as per the instruction manual and the video and I even emptied the bed and cleaned it before second attempt. there were remnants of the attempted on the film but nothing adhered to the plate. Do I need to re-level in closer? The paper had resistance but not a lot when I leveled it.

翻譯年糕

Matt Dowis
2019-08-31 03:50:05