Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Rene Canlas
2019-11-26 23:38:12

Anyone?

有人嗎?

· 查看原文 · 為此翻譯評分

Patrick Haeflinger
2019-11-26 23:51:17

Matt Hooton
2019-11-27 00:15:32

Rod Williams
2019-11-27 00:36:37

André Nettermann
2019-11-27 01:35:54

Rene Canlas
2019-11-27 01:49:31

Johnny Johnsen
2019-11-27 04:22:39

Samson Chen
2019-11-27 04:36:57

Rod Williams
2019-11-27 06:59:17

Johnny Johnsen
2019-11-27 07:00:02

原文網址 Rene Canlas
2019-10-14 14:23:29

Given that the best way to dispose of waste resin is to cure it fully, do you just leave your trash out in the sun (hopefully no pets around) or do you have a special rig for curing your resin trash before disposing?

翻譯年糕

Mark Wardle
2019-10-14 15:03:01

Niall Forrester
2019-10-14 18:19:32

Jeff Greenfield
2019-10-14 21:39:24

Nick Taylor
2019-10-15 02:03:31

原文網址 Rene Canlas
2019-10-03 19:33:59

Help! I have an .stl file which shows up fine in the photon slicer, but when I try to open it using ChituBox 1.5, it opens but the model is nowhere to be found. I don't even see the build platform. Anyone else encounter this? Tips on how to fix?

翻譯年糕

Dai Buckley Oam
2019-10-03 19:44:37

Rene Canlas
2019-10-03 19:47:44

David Collinson
2019-10-03 19:49:46

Marc de Hoogh
2019-10-03 19:50:28

Aiden Sone
2019-10-03 20:20:10

Arnie Locsin
2019-10-03 20:56:52

Rene Canlas
2019-10-03 20:59:19

Robert James
2019-10-03 21:30:17

Aiden Sone
2019-10-03 22:21:40

Arnie Locsin
2019-10-04 00:13:10

Aaron McCommon
2019-10-04 09:48:09

David Collinson
2019-10-04 17:32:05

David Collinson
2019-10-04 17:33:37

原文網址 Rene Canlas
2019-09-26 11:36:06

Models I printed 2 days ago started cracking. I read this is due to uncured resin inside that is expanding. There is already a drain hole but it looks like it fused closed when i was curing under a UV light. Thoughts? TIA

翻譯年糕

Aaron Wiggins
2019-09-26 11:36:40

Antonio Robbins
2019-09-26 11:39:45

Elle Heilig
2019-09-26 11:49:06

Mark Wardle
2019-09-26 11:52:33

Sean O'Hayer
2019-09-26 11:53:16

Rene Canlas
2019-09-26 11:54:07

Greg Kourakos
2019-09-26 12:00:07

Elle Heilig
2019-09-26 12:09:36

Doc Tornado
2019-09-26 12:26:18

Elle Heilig
2019-09-26 13:36:48

Doc Tornado
2019-09-26 14:06:27

Elle Heilig
2019-09-26 14:07:09

Doc Tornado
2019-09-26 14:09:39

Pierre Maugard
2019-09-26 16:21:49

Christopher Botha
2019-09-26 17:28:28

Christopher Botha
2019-09-26 17:30:49

Christopher Botha
2019-09-26 17:30:56

Christopher Botha
2019-09-26 17:31:03

Rene Canlas
2019-09-26 17:43:29

Christopher Botha
2019-09-26 17:44:14

Rene Canlas
2019-09-26 17:49:25

Rene Canlas
2019-09-26 17:51:14

Christopher Botha
2019-09-26 17:51:28

Vinicius Silva
2019-09-26 17:55:57

Sercan Güzel
2019-09-26 21:23:05

Rene Canlas
2019-09-26 21:25:21

Rob Mayberry
2019-09-26 21:56:22

Rob Mayberry
2019-09-26 21:58:34

Stefan Giudici
2019-09-26 23:19:38

Dan Jay
2019-09-27 04:34:25

Dan Jay
2019-09-27 04:34:53

Rob Mayberry
2019-09-27 04:57:55

Guifré Ibarz
2019-09-27 06:15:33

Rigo Arevalo
2019-09-27 12:57:28

Rene Canlas
2019-09-27 13:09:01

Rigo Arevalo
2019-09-27 13:11:47

原文網址 Rene Canlas
2019-09-24 15:34:55

Ran out of resin in the middle of a print job. Wondering if I can build a mechanism to supply the vat continuously with resin... What type of mechanism can be used to stop the flow once the resin reaches the desired mark...

翻譯年糕

Alex Winniczuk
2019-09-24 15:39:44

Bob Deblier
2019-09-24 15:40:03

Onesimo Guzman
2019-09-24 15:50:06

Jerry Mojares
2019-09-25 12:54:48

Herman Simpson
2019-09-26 04:59:12

原文網址 Rene Canlas
2019-09-23 00:40:37

Noob question...It says on the bottle that Monocure 3D gray resin cures between 225-420nm. If I get a UV lamp for curing, does getting one with a higher wavelength (370nm vs 420nm) help in any way? TIA!

翻譯年糕

Brendan Rose
2019-09-23 00:46:51

Michael James
2019-09-23 01:59:15

原文網址 Rene Canlas
2019-09-18 12:15:18

Got a good deal for a slightly used Photon S for $150. So far everything checks out but id like to ask the veterans and experts here about my first 2 prints. I noticed warping on the cube where it intersects with the logo. How to prevent? Thanks for any feedback. I used gray monocure resin. The failed print is supposed to be the boat (3DBenchy)

翻譯年糕