Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Joseph Daniels
2020-02-14 20:27:00

All right, we know the little "clicks" are OK for the first bit of a print, but what about throughout the WHOLE print? I get the feeling I'm setting 0 too low on my S. Might explain why I got two good prints, then the rest have been total failures...

翻譯年糕

Nipuna Gunarathne
2020-02-14 20:50:00

Scott Pavlich
2020-02-14 21:19:23

原文網址 Joseph Daniels
2020-02-13 01:52:32

Well, got my S after the light array on my original died, and so far I waaaay overexposed my calibration prints. I'm guessing on the S I should be reducing exposure times rather than extending?

翻譯年糕

Alexander Bayerdorffer
2020-02-13 02:03:26

Joseph Daniels
2020-02-13 02:10:26

Sander van Deijl
2020-02-13 05:59:21

原文網址 Joseph Daniels
2020-02-04 10:27:06

I crashed my laptop trying to add supports to this thing to print on my Photon. I wish I was kidding.
https://www.thingiverse.com/thing:35009

Anyone have this thing already supported? Or suggestions on how TO support it, without having to slice it in to smaller bits? Trying to keep it at the same scale as the original STL, for a bigger model. 翻譯年糕

Anthony Tapp
2020-02-04 10:37:04

Joseph Daniels
2020-02-04 10:39:14

Anthony Tapp
2020-02-04 10:39:38

Anthony Tapp
2020-02-04 10:41:29

Joseph Daniels
2020-02-04 10:42:07

Joseph Daniels
2020-02-04 10:44:14

Anthony Tapp
2020-02-04 10:47:56

Joseph Daniels
2020-02-04 10:52:10

Anthony Tapp
2020-02-04 10:55:54

Joseph Daniels
2020-02-04 11:01:51

Jason Schilling
2020-02-04 11:42:04

Kempster Kevin
2020-02-04 12:36:41

Kempster Kevin
2020-02-04 12:38:31

原文網址 Joseph Daniels
2020-01-29 09:08:37

CRAP.

Bottom panel slipped off the table entirely during a screen replacement. Does anyone have a diagram of where the fan cables are connected and a good lead on a replacement if necessary?

翻譯年糕

John Aldred
2020-01-29 09:14:09

Nick Eason
2020-01-29 09:21:01

Joseph Daniels
2020-01-29 10:00:46

James Cachia-Garrett
2020-01-29 10:32:45

James Cachia-Garrett
2020-01-29 10:33:00

Alvaro Rodriguez
2020-01-30 03:12:53

Alvaro Rodriguez
2020-01-30 03:13:46

Alvaro Rodriguez
2020-01-30 03:17:30

Joseph Daniels
2020-01-30 03:18:00

Alvaro Rodriguez
2020-01-30 03:19:01

原文網址 Joseph Daniels
2020-01-23 09:25:40

Well, my fan inside the print chamber is definitely dying. I thought it was just unbalanced or dirty, but nope, not so easy.

Does anyone have a link for a reliable, easily-installed replacement?

翻譯年糕

Stefan Giudici
2020-01-23 09:30:05

Joseph Daniels
2020-01-23 09:30:57

Stefan Giudici
2020-01-23 09:33:48

Simon Richards
2020-01-23 09:34:04

Joseph Daniels
2020-01-23 09:34:23

Aaron McCommon
2020-01-23 09:39:36

原文網址 Joseph Daniels
2020-01-16 20:54:13

Once I wrap up my last print or two with my remaining Elegoo Grey, I'm gonna take a swing at the Polyjuice Clear. Does anyone have any tips beyond what Filaments.ca put on their page? How good are those settings?

翻譯年糕

Randy Shepherd
2020-01-16 21:03:23

Jeremy Babcock
2020-01-16 21:06:23

Jeremy Babcock
2020-01-16 21:07:26

Alex Danis
2020-01-16 21:47:21

Alex Danis
2020-01-16 21:47:46

Joseph Daniels
2020-01-16 21:50:19

Alex Danis
2020-01-16 22:08:40

Alex Danis
2020-01-16 22:09:36

Joseph Daniels
2020-01-16 22:13:13

Alex Danis
2020-01-16 22:45:09

Joseph Daniels
2020-01-16 22:47:55

Joseph Daniels
2020-01-18 10:22:00

原文網址 Joseph Daniels
2019-12-18 21:26:28

Nailed it!

(I already know what went wrong. I just thought it was funny.)

翻譯年糕

原文網址 Joseph Daniels
2019-11-07 22:23:00

Glorious.

光榮.

· 查看原文 · 為此翻譯評分

Joe Brislane
2019-11-08 04:15:14

Joseph Daniels
2019-11-08 04:19:51

Joe Brislane
2019-11-08 04:24:16

Phillip Kenney
2019-11-08 05:09:28

Joseph Daniels
2019-11-08 07:31:19

原文網址 Joseph Daniels
2019-10-06 22:24:41

I've had "artifacts" on my last two prints, for lack of a better word, and I'm not sure why. Using the same resin and the same settings, other prints have been just fine. Gonna try a calibration slice for S&Gs, but it's still odd. Anyone have any insight?

Anycubic clear, pigmented purple.
0.02 thickness,16s on, 5s off, 8 bottom layers at 100s.

翻譯年糕