Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 David Friedberg
2020-01-14 13:01:44

This is my first model with supports took a while to get them off. It could use a little sanding but it's very delicate still have to cure it.

翻譯年糕

Zak Williams
2020-01-14 13:21:23

David Friedberg
2020-01-14 13:29:38

Zak Williams
2020-01-14 13:33:22

原文網址 David Friedberg
2020-01-12 09:52:43

Was able to get two successful prints today. Printed the chess piece directly on bed. On the fallout 76 door I came get it clearly in the photograph but it came out very detailed all fine lines are perfect. Used Chitubox for slicing and supports on Fallout door.

翻譯年糕

原文網址 David Friedberg
2019-12-17 05:36:35

Printed cube came out fine. So I found a model that already had supports already. I made 2 mistakes I assume in exposure it stick to the FEP. I didn't realize that and saw the plate clean and reprinted so the print just stuck to the FEP I couldn't get it off. So I changed the FEP. I failed print popped off on it's own when I loosened the second screw. In any event in back where I started and not printing the cube again. Buy the way the FEPs included have a plat of protector on each side you have to remove.

翻譯年糕

Handrez Pintubola
2019-12-17 05:44:25

David Friedberg
2019-12-17 05:46:08

Ian Gill
2019-12-17 06:40:10

David Friedberg
2019-12-17 07:33:33

原文網址 David Friedberg
2019-12-14 04:47:38

I’m new to the 3D space I just cleaned and cured my test print for about 5 minutes on each side In a proof box. I’m not sure where to get models to print. I’m going to make my own using blender eventually. I’m just looking for simple stuff like cartoon characters, or something like a speed racer car. Free or Paid.

翻譯年糕

Chris Rhodes
2019-12-14 04:53:17

Brianw NJcsx
2019-12-14 04:53:26

Thomas Harrell
2019-12-14 04:55:05

Smith Hayward
2019-12-14 05:03:22

Smith Hayward
2019-12-14 05:03:48

David Friedberg
2019-12-14 05:13:09

Thomas Kenneth Scheer
2019-12-14 05:27:22

Vernie G-graphy
2019-12-14 06:37:38

Joe Fillion
2019-12-14 06:49:02

Vernie G-graphy
2019-12-14 07:12:14

David Friedberg
2019-12-14 13:40:46

原文網址 David Friedberg
2019-12-13 20:44:18

Test print came out ok I think. I’ll take it off tonight to see. I used the Flint Reed method to calibrate the bed.

翻譯年糕

Nicolas Tsagarides
2019-12-13 21:02:37

原文網址 David Friedberg
2019-12-13 10:33:36

I finically received my Kapton tape. I leveled the plate with the flint reed method, and I’m currently printing the test cube. I filled the basin up a tiny bit passed where the flat walls stop. Is this enough resin to complete the test cube and if I leave it over night will that affect the liquid resin so it can’t be rinsed in the morning?

翻譯年糕

Scott Pavlich
2019-12-13 10:37:19

Jarin Udom
2019-12-13 10:37:55

Mark Wardle
2019-12-13 10:38:19

Edric Chua
2019-12-13 10:40:26

David Friedberg
2019-12-13 10:45:59

Kenneth Keenaghan
2019-12-13 10:54:06

Mark Wardle
2019-12-13 10:56:46

Kenneth Keenaghan
2019-12-13 10:57:26

Mark Wardle
2019-12-13 11:25:20

原文網址 David Friedberg
2019-12-11 12:36:29

I want to apply Kapton tape or a gasket to my screen. I haven’t used the printer yet. It there a way to activate the screen light so I don’t tape over the exposure area?

翻譯年糕

Andrew Gott
2019-12-11 12:38:39

David Friedberg
2019-12-11 12:40:20

Sam Giardina
2019-12-11 12:59:20

Tiernan Messmer
2019-12-11 14:06:47

原文網址 David Friedberg
2019-12-06 11:16:34

I just purchased the Photon S on Amazon sale. Waiting for screen gasket to arrive before printing. I don’t have a PLA printer but my coworker was nice enough to print this curing box for me on his upgraded Prusa MK2.

翻譯年糕