Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Damian Power
2020-03-21 08:43:56

Some advice please
Trying to replace my screen and man it’s fiddly
I watched the anycubic vid a few times and thought I’d have a go

I feel like I’ve got the power attachment into the motherboard
It clicks in and sits flush but my uv test still suggests I’ve not done it right
Any Suggestions?

翻譯年糕

Rolando Gutierrez
2020-03-21 09:06:40

I'm currently in the same predicament. I replaced the LCD today and getting the same results. I then switched to another LCD from a different manufacturer but no change. I put in for a ticket with Anycubic. Let's see what they come up with.

Robert Mun
2020-03-21 11:07:24

What type of LCD screen? If it is the Mars one, I believe you have to use an adaptor. Plugging the wrong one in can fry the motherboard. In you case it looks like it may not be plugged in properly

原文網址 Damian Power
2020-03-18 22:43:40

I’m assuming this is a problem with the uv screen?....
3 months of solid use though... :-)

翻譯年糕

Mike Tongue
2020-03-18 22:46:14

yep, new screen time

Mike Tongue
2020-03-18 22:46:36

just check its not resin on the top .. but doesnt look like it

Damian Power
2020-03-18 22:48:07

Mike Tongue thanks Mike

Dylan Foonk
2020-03-20 21:29:15

We had this exact issue with one of our machines and we had to replace the LCD to fix it, unfortunately.

原文網址 Damian Power
2020-01-29 17:44:44

Wow
Just reflected on my first month 3D printing...

I’ve worked out that I’ve made
6 monsters (mostly artisan stuff- a giant and. Ogre, a spider, a flying saurus, a large kroxigor sc and a scrap heap golem...!!)
200 infantry (100 halflings, 90 hobgoblins, 15 skaven)
25 cavalry (hobgoblin wolf Rider and halfling pony cavalry)
And lots of small scenery- campfires/mining equipment in my first month
And used exactly 3 bottles £40 resin

This is utterly bonkers....
Changed one FEP and used A LOT of gloves...

翻譯年糕

Gustaf Sjögren
2020-01-29 18:04:32

Damian Power
2020-01-29 18:10:56

Gustaf Sjögren
2020-01-29 18:25:20

Gustaf Sjögren
2020-01-29 18:33:25

Ethan Zachary
2020-01-29 20:14:43

Tadeu Levy
2020-01-29 20:20:53

Jens Verwaest
2020-01-29 20:55:50

Tauri Icenogle
2020-01-29 21:41:51

Jason E Heuer
2020-01-29 22:52:21

Neil Racka Rackstraw
2020-01-30 17:09:55

Nicholas Corea
2020-02-03 23:35:48

原文網址 Damian Power
2020-01-17 08:06:32

I’ve had a busy day
Heroforge blows my mind
I’m building a halfling army for warhammer fantasy battle

Made a few minis before I had my printer (using the black Friday deal) - but today set 5 plates going with 10 halflings on each
A successful day....

翻譯年糕

Charlie Yoshi Locke
2020-01-17 08:07:52

Damian Power
2020-01-17 08:08:33

Damian Power
2020-01-17 08:10:27

Cody Wishart
2020-01-17 12:12:45

Damian Power
2020-01-17 15:21:07

Nicholas Corea
2020-01-17 15:58:22

Dave Green
2020-01-17 16:39:52

Damian Power
2020-01-17 17:18:53

Damian Power
2020-01-17 17:20:04

Dave Green
2020-01-17 17:21:00

Andrew Stockton
2020-01-17 22:03:02

原文網址 Damian Power
2020-01-05 22:51:05

A bit of advice please

First of all- blown away with the photon- had for 2 weeks and gone through 1l grey gloop with lots of successful prints

I’m pretty sure my lcd screen has some resin/baked cured onto it
There’s some mild roughness to touch and my last 2 prints have had a very mild print error in what looks like a corresponding area

Is that likely that 1-2mm
Resin under the vat is interfering with the print
( I would assume it’s absorbing/interfering with the UV light getting to the print surface??)

And the instructions say alcohol on a cloth but so far that hasn’t got it off

How hard can I remove
Any advice how if a wash with IPA isn’t working ?

Many thanks in anticipation

翻譯年糕

Kory Sebby
2020-01-05 22:54:12