Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Richard Burke
2020-03-11 08:09:36

Switched to Grey when the green ran out. Everything seemed to be going okay. Until I noticed that a couple of the prints were pulled off the supports. And this Caster has some weird layering going on I'm curious if maybe all of these issues are not having my exposure correct? I saw the spreadsheet but I'm curious because I've read that the photon S needs shorter times than the original photon. Is there anyone using the anycubic Grey that would be kind enough to share this settings they're having for successful print so I can try again? Or maybe someone can tell me that I did something else wrong

翻譯年糕

Jason Pedersen
2020-03-11 08:13:18

Richard Burke
2020-03-11 08:16:37

Jason Pedersen
2020-03-11 08:23:06

Richard Burke
2020-03-11 08:25:24

Jason Pedersen
2020-03-11 08:30:29

Richard Burke
2020-03-11 08:34:22

Jason Pedersen
2020-03-11 08:43:14

Jacob Palmer
2020-03-11 16:03:29

原文網址 Richard Burke
2020-03-09 02:14:39

I searched the group first and I see a lot of people having To re-level after they change the FEP. But what would be giving me the issue that I have to re-level the bed almost every print?

翻譯年糕

Richard Shapiro
2020-03-09 02:15:57

Sen Kun
2020-03-09 02:18:19

Richard Burke
2020-03-09 02:19:33

Richard Shapiro
2020-03-09 02:20:57

Richard Burke
2020-03-09 02:23:45

Richard Burke
2020-03-09 02:24:23

Richard Shapiro
2020-03-09 02:26:32

Richard Burke
2020-03-09 02:30:26

Richard Shapiro
2020-03-09 02:37:24

Chris Holden
2020-03-09 02:55:35

Keith Yinger
2020-03-09 04:54:34

原文網址 Richard Burke
2020-03-08 10:52:45

I had several successful prints. Started a print when I went out to eat with the family came back and it was only about halfway done. With part of the print hanging from the build plate. There was no buildup on the bottom. So I re sliced it and tried again. This time this is what I got and these were stuck to the bottom and had completely detach from the build plate. Confused because i had 3 great prints befor it started these issues. Im printing with the Photon S.

翻譯年糕

Christian Savarda
2020-03-08 22:15:45

原文網址 Richard Burke
2020-03-07 14:09:43

So. Got my printer working well. Hot water fixed my support issue. Now i have this white residue poping up. What is the cause of this. How to if i need to avoid it? Will it interfere with primeing and painting ?

翻譯年糕

Mike Kelso
2020-03-07 14:11:08

Nipuna Gunarathne
2020-03-07 14:17:14

Richard Burke
2020-03-07 14:25:41

David Belshaw
2020-03-07 14:55:50

Fred Bey
2020-03-08 00:03:59

Herllon Alves
2020-03-08 06:23:51

原文網址 Richard Burke
2020-02-27 11:41:43

So I just got my Photon s. And I'm curious on the printing process. Can you print overnight and come back hours later to clean up the model and cure it. Will the resin be okay. Or do I need to jump on top of it as soon as it finishes. Just trying to get an idea of the time frames. And kind of trying to work printing into my schedule. Like it would be awesome if I could start a print before I go to work and come back 10 to 12 hours later and it be ready for me.

翻譯年糕

Jeremy Swigart
2020-02-27 11:43:58

Alexander Lew
2020-02-27 11:45:06

Richard Burke
2020-02-27 11:46:25

Hugh Jeriolas
2020-02-27 11:49:36

Richard Burke
2020-02-27 11:50:13

Keith Yinger
2020-02-28 00:48:50

Keith Yinger
2020-02-28 00:50:15

Chris Robinson
2020-02-28 01:36:55

Rick Hanson
2020-02-28 02:01:45

Keith Yinger
2020-02-28 02:41:42

原文網址 Richard Burke
2020-02-26 11:19:56

Hello. Just got the photon s. Have spent the last 4 hours trying to get it to read files. My thumb drive and the one that came with it comes back blank. Even when trying to update the firmware. Any help and guidance would be appreciated.

翻譯年糕

Kurt Brown
2020-02-26 11:39:36