Anycubic Photon Printer Owners 造訪社團

UPDATE:Thanks everyone! This first round of pre-orders is now closed! We will now be accepting further orders once the kit is actually in Paul's hands!

-------------------------------------------------

I figured I'd post this here, since I'd been sharing my progress with everyone! But this is my official ¼ Clint Eastwood – Man with No Name Bust Pre-order Post:

I wanted to start an official pre-order post for the 1/4 Clint Eastwood as the Man with No Name/Blondie bust. The assembled piece will stand 25 cm tall. A $45 deposit is required to get on the list.

The images seen below were taken of the bust printed on my Anycubiic Photon and while it came out really nicely, I feel like some of the smaller details got lost. As a result, the final print will be handled by Ownage. We want to make this the end-all-be-all Eastwood bust ?

So in short, your print will be the exact same design, but will hold even more detail! See the image of the digital sculpt for reference.

Just to show the quality of Ownage’s 3D printing services, I’ve also included a screenshot of print work they did of a Logan and Daniel Craig sculpt. Those were 1/6 scale by the way! So this bust will look amazing.

The final print will be completed by the end of next week and will be sent to Paul Gill who will be handling all of the molding and casting. The final bust is anticipated to ship late December into January.

The price of the model is: $90 + shipping and handling.

US shipping range estimates: $10-20

International shipping estimates: At least $50 – but these will have to be estimated on a case by case basis.

Please note that these shipping and handling costs are estimates and are not included in the price of the bust itself.

Again, a $45 deposit is required to get on the list. Let’s make this happen! ? PM me to get payment info and to get on the list.

翻譯年糕

My first miniature for a customer. Sorry for bad pics. I guess its turned out acceptable. AC green. 5 bot layer 55sec, 0.05 lh 9 sec.

翻譯年糕

The thing I love about the photon is when you get things working you can just get into a groove. Really loving this elegoo clear red more than I thought I would! 0.05 and 12s

翻譯年糕

New photon s owner :)
Just printed an alien tourist boardgame figure

翻譯年糕

Wanted to give a shout out to Greg Kourakos for his support tips in chitubox and his tips on taking good pics of your minis. Heres a few pics of minis done with his style supports. With alittle hot water there was ZERO spru cleanup.

翻譯年糕

Hey Guys and Girls,

As some of you know I've been working on this little project of mine for a while now but we are finally ready to give it a go with our kickstarter launch!!

The entire project was designed using Fusion 360 and prototyped using a mix of the anycubic photon and a creality CR-10, I think it's a perfect example of something to show case a start-up product example.

Would mega appreciate you all to like and share the page / post and link so we can get as much attention as possible!

Wish me luck guys. Also for those of you that are interested in the product itself, if we are successful in raising our needed funds we will be giving away 5 units to some lucky draw winners!

We will officially launch our campaign from the 22.11.19 Fingers crossed!

Thanks for all your support!

翻譯年糕

Hi i need help with my printer.
Any advice?

翻譯年糕

Looking for some advice from the experts: having problems with random reboots after first layer is printed..

This is on an original Photon. I have seen the problem a few times before, but recently it is happening >50% of the time I start a print. Basically the print starts as normal, the plate goes down to z=0 and the layer is exposed for the appropriate time (say 80 or 100s). Next the plate either raises slightly or not at all, the printer stops for a few seconds (blank display) then reboots back to the start screen. There is no way to continue the print The first layer has printed fine and is stuck nicely to the plate.
I have done a fair bit of fault-finding. Some observations: It happens with different models. It does not seem to be a corrupt file as it will sometimes work on the second or third attempt with the same file. Have tried three or four different USB sticks. Same problem regardless When the print gets past the first two or three layers, it usually seems to succeed. I have otherwise had very successful prints with nice detail and I am not seeing any problems with levelling etc. I typically do not re-level beween prints, but I have tried doing so and it does not seem to make any difference to this issue. Problem is seen with both 0.02 and 0.05 layer heights.
This weekend, I decided to throw everything at it, and did the following: Updated firmware to 4.2.18 Replaced power brick with a good quality one (from RS online) rated at 12V, 7A Replaced internal USB extension cable (also RS online) Bought new Sandisk USB drive (16Gb), newly formatted with FAT32 Cleaned and carefully lubricated Z-rod with lithium grease. I started a print with a plate full of small parts and it failed as described above. Without changing anything (not even removing USB from slot, or even removing the cured resin from the printer), I started the print again. It failed a second time. As the layers are only 0.02mm, I figured I could get away with one more attempt without removing the cured resin, so again, I restarted the same file on the same USB without changing anything. The first seven or eight layer have gone fine, I could hear the click of the print pulling off the FEP and I hope it is still running. I have done something similar once before and had a perfect print on the second or third attempt. Having worked with fault-finding various machines for most of my working life, I have learned that 'gut-feelings' cannot really be trusted. Having said that, this feels a bit like something is happening when the motor is under most strain (a fair proportion of the plate is covered in support bases, and the cure time is of course extended for the first layers). Considering the things I have already replaced, there isn't much left to try: maybe I can look at reducing the bottom layer times. Otherwise I am worried the problem is with the mainboard (or the motor/driver?)
Any suggestions? 翻譯年糕

Undead pirate captain from Cast n Play Photon S Elegoo Grey .04

來自cast的不死海盜隊長玩photon s elegoo grey. 04年

· 查看原文 · 為此翻譯評分

*****
Update :
So after 4 days of curing the model (model was outside, day & night, unfortunately I can not remember whether we had some other but cloudy days for last days ..) and model is still meh ..

What comes to my mind is, to use the light from printer it self - there is a "test light" or something function..

I don't have curing station yet, so .. did any one try it ?

*****

Hey guys, quick question. If not light cured model has been primed, is it possible to cure it somehow, or it's model lost?

Thanks

翻譯年糕