Anycubic Photon Printer Owners 造訪社團

原文網址 Daeron Grajales
2019-10-22 10:10:34

lets try it.

翻譯年糕

Cai Lansdown
2019-10-23 06:29:16

原文網址 Jake Gilmore
2019-10-22 09:52:24

原文網址 Grace Ma
2019-10-22 09:48:00

Anycubic Photon S Halloween Giveaway, Good luck! ?

翻譯年糕

原文網址 Robert Small
2019-10-22 09:45:41

Atlas update.

翻譯年糕

原文網址 Ade Sanya
2019-10-22 09:30:56

Can anyone tell me why this is happening? 8ts my 2nd print where I printed 4 figures and only 1 actually survived. The other 3 are stuck to the bottom of the bath... Again.

翻譯年糕

Ian Chess
2019-10-22 09:32:03

Ade Sanya
2019-10-22 09:43:27

Andrew M Dunlap Jr.
2019-10-22 09:44:38

Ian Chess
2019-10-22 10:18:33

Ade Sanya
2019-10-22 11:15:34

Ian Chess
2019-10-22 11:23:27

Doug Bowman
2019-10-22 21:46:36

Ade Sanya
2019-10-22 22:09:06

Ade Sanya
2019-10-22 22:09:21

Ade Sanya
2019-10-22 22:10:01

原文網址 Michael Paulick
2019-10-22 09:25:18

Here's a question I haven't seen yet: When I hollow my model, I run the auto supports and it fills up a goodly portion of my model on the inside with supports. This also serves to effectively plug the drain hole(s) that I put in.
Am I doing this wrong or missing something?

翻譯年糕

Andy Macdonald
2019-10-22 09:44:51

Michael Paulick
2019-10-22 09:53:08

Andy Macdonald
2019-10-22 10:03:53

Michael Paulick
2019-10-22 10:10:43

原文網址 Michael Martin
2019-10-22 09:20:01

I need to update my firmware. Which version should I use? (Haven't updated in ~ 5 months)
Thanks!

翻譯年糕

Jorge Reyes
2019-10-22 13:30:14

Chayanin Somton
2019-10-22 14:14:18

Michael Martin
2019-10-22 18:17:38

Evan Miller
2019-10-22 23:10:56

Evan Miller
2019-10-22 23:11:20

Jorge Reyes
2019-10-22 23:36:38

Jorge Reyes
2019-10-22 23:36:59

Sen Kun
2019-10-22 23:41:32

原文網址 Brian Corbin
2019-10-22 09:19:02

Printed in two parts and glued. Used Anycubic clear resin with a few drops of resin dye. 9 hours.

翻譯年糕

原文網址 Dan Cowan
2019-10-22 09:04:43

Doing my first print with polyjuice water washable resin tonight ***UPDATE*** so the initial smell and smell when printing is just as bad as any other resin. However post printing the parts smell less and hardly smell at all when curing. i did two test pieces very small and am curing one in just water one in ipa. Looks good so i am doing a large print that i will post pics and review.

翻譯年糕

Ian Chess
2019-10-22 09:33:40

Evan Brand
2019-10-22 09:35:57

Dan Cowan
2019-10-22 09:36:53

Andrew Sternglass
2019-10-22 09:41:40

Dan Cowan
2019-10-22 09:44:20

Andrew Sternglass
2019-10-22 09:45:56

Dan Cowan
2019-10-22 09:46:09

Dan Cowan
2019-10-22 09:46:17

Dan Cowan
2019-10-22 09:48:57

Todd Swindoll
2019-10-22 09:54:09

Dan Cowan
2019-10-22 10:08:40

Stefan Giudici
2019-10-22 10:10:38

Abdul Hanan Ismail
2019-10-22 10:10:54

Lee Johnson
2019-10-22 10:18:08

George Graves
2019-10-22 10:48:27

Dan Cowan
2019-10-22 11:04:05

Sam Farmer
2019-10-22 12:29:16

John Chrapkowski
2019-10-22 12:57:58

Stefan Giudici
2019-10-22 13:22:12

Clifford Schwankner
2019-10-23 01:49:54

原文網址 Eddie Sells
2019-10-22 08:48:35

Three days, three tries and I am yet to make my first successful print. My first attempt was the Photon cube. It came out okay but a the base was a little wonky and the word "photon" inside the cube was deformed. This was almost certainly due to not having the Z set properly. I reset the Z and tried again.

I soon had an idea that this wasn't going to work since I could see that the print platform did not stay straight, apparently I did not tighten down the grub screw as tight as I should have. After the platform had risen enough it was clear that the raft detached from the platform and so I had nothing but a little half-formed wafer setting loosely in the vat. I set the Z again.

I was pretty confident about my third attempt. I was sure that the platform was level and that the grub screw was tight. After a few hours I was able to see that everything looked level but again there was no raft attached to the platform. This time the raft was affixed to the FEP instead of the Platform.

Maybe I had the Z set too tightly to the UV LED? I was able to remove the paper with resistance, but maybe it was a little too much resistance. I have reset the Z and will prepare for my fourth attempt tomorrow.

翻譯年糕

James Byberg
2019-10-22 08:55:01

Joe Cahill
2019-10-22 09:08:36

Eddie Sells
2019-10-23 09:57:59

討論主題

發文排行榜

回文排行榜

熱門關鍵字