Anycubic Photon Printer Owners 造訪社團

原文網址 Weston Miller
2019-10-10 01:03:48

Was searching through the Google sheet looking for rubber like resins. I seen a few. Who all has person experience with them? Curious what ya liked and didn't like.

翻譯年糕

Craig Tinerella
2019-10-10 01:07:15

Weston Miller
2019-10-10 01:10:29

Craig Tinerella
2019-10-10 02:07:28

Ian Chess
2019-10-10 07:03:07

原文網址 Oliver Stubley
2019-10-10 00:58:45

A few times now I have come back to a print that says it has finished, but the Z axis has stopped moving up mid print. What could cause this?

The z axis moves fine when I lift it back up afterwards. Not using the original USB, so don't think it's file corruption. Any ideas?

翻譯年糕

原文網址 William David Cunningham
2019-10-10 00:12:10

Rene Santos
2019-10-10 00:57:17

William David Cunningham
2019-10-10 01:20:36

Eric Ilaqua
2019-10-10 01:20:57

Rene Canlas
2019-10-10 01:50:46

Pablo Arizpe Garza
2019-10-10 02:23:28

Jesse DeGraff
2019-10-10 07:45:45

William David Cunningham
2019-10-10 07:51:16

Edward Michael Lopez
2019-10-10 23:33:06

William David Cunningham
2019-10-11 03:50:00

原文網址 Jay Dubbs
2019-10-10 00:00:28

I'm trying to print this part, I have it set at a 20 degree angle on the bed, it comes off the print non warped. Can anyone give me any ideas why its warping after the fact? I washed it in IPA for like 5 min, which I know isn't enough but I don't think that would warp it like that. It has been uv cured for like 1 min on each side. Thanks in advance.

翻譯年糕

Matt Hooton
2019-10-10 00:18:10

Jay Dubbs
2019-10-10 00:31:49

Jay Dubbs
2019-10-10 00:32:15

Matt Hooton
2019-10-10 00:36:37

Jay Dubbs
2019-10-10 00:38:18

Jay Dubbs
2019-10-10 00:39:05

Jay Dubbs
2019-10-10 00:39:29

Matt Hooton
2019-10-10 00:40:11

Jay Dubbs
2019-10-10 00:44:53

Gabe Snooks
2019-10-12 03:31:38

原文網址 Rob Davidson
2019-10-09 23:12:38

Well, I’ve took the plunge, bit the bullet and ordered a
UK ANYCUBIC Photon S SLA LCD 3D Printer UV Resin Light-Cure 2.8" TFT Dual Z-axis and it comes next Wednesday apparently.
Then the questions begin to flood the group. ? ?

翻譯年糕

原文網址 Joey Pruitt
2019-10-09 22:58:02

The latest sculpt and print, almost ready for paint.
14" tall including the legs.

翻譯年糕

Vlado Turek
2019-10-10 00:32:02

Rastko Stanojevic
2019-10-10 05:41:16

原文網址 Elodie Renou
2019-10-09 22:55:46

Bonjour, Nous essayons actuellement d'imprimer avec une résine très pâteuse sur une photon. Je voulais savoir si il y avait possibilité de bloquer le plateau en hauteur quelques seconde entre chaque couche afin que la résine se remette de niveau. Si oui, comment faire cela svp ?

Hello, We are currently trying to print with a very pasty resin on a photon. I wanted to know if there was a possibility of blocking the tray height a few seconds between each layer so that the resin is level. If so, how do you do that?

翻譯年糕

Tiernan Messmer
2019-10-09 23:05:21

Nipuna Gunarathne
2019-10-11 22:31:12

原文網址 Devin Wallace Simonsen
2019-10-09 22:45:50

so I just opended my package to find they're the wrong filters... ? :( 280nm rather than 125nm and far to large compared to the ones I ordered (more than twice the diameter)
anybody know if they can still be used or should I see if I can borrow some from my school until the right ones arrive? 翻譯年糕

Sean Croteau
2019-10-09 22:49:26

Tiernan Messmer
2019-10-09 22:56:18

原文網址 Jonathan Stokes
2019-10-09 22:45:25

Another giveaway everybody!

翻譯年糕

Ryan Dow
2019-10-11 10:00:35

Thomas Riepe
2019-10-12 15:45:13

Jonathan Stokes
2019-10-13 02:43:23

Jonathan Stokes
2019-10-13 02:44:55

Mark Wardle
2019-10-14 09:11:05

原文網址 Matthew Kuka
2019-10-09 22:45:17

tried a new litho with anycubic white and had some aqua blue bleed over, not sure why as the vat was cleaned before start, the only thing I can think of is that cleaning in the previously used IPA led to bleed over. still turned out decent.

翻譯年糕