Anycubic Photon Printer Owners 造訪社團

原文網址 Stephen Lewis
2019-09-07 21:51:14

What would cause the File Validator to not scan the layers of a particular file? No settings have changed in my ChituBox slicer and a file created before the file in question scans and reports islands.

翻譯年糕

Stephen Lewis
2019-09-07 21:56:05

Chad Elstad
2019-09-07 21:57:21

Stephen Lewis
2019-09-07 21:59:47

原文網址 Arthur Withier
2019-09-07 21:44:26

Ready for UV curing ? i want make cube in miror in the future

翻譯年糕

Pataki Ábris
2019-09-07 23:52:28

Chris Meijer
2019-09-08 03:39:27

Ricky Wong
2019-09-08 19:11:52

Arthur Withier
2019-09-08 19:29:58

Omar Osman
2019-09-08 20:47:56

Arthur Withier
2019-09-08 21:47:27

原文網址 Jake Fry
2019-09-07 21:39:41

Hey guys. Had my photon few days now. Absolutely loving it. (I had a d7 before and they just don't compare)

I know you guys say you know its fully cured when you can't scratch it with your nail anymore. But what about the insides of it? Especially if it's hollow.

Some of my prints when i had a d7 would split open even after being cured for ages and i'm concerned the same thing will happen again.

Any information will be great and i did use the search for this but it was just a plethora of answers.

翻譯年糕

Chad Elstad
2019-09-07 21:44:30

Jake Fry
2019-09-07 21:48:59

Chad Elstad
2019-09-07 21:52:18

Ben Lord
2019-09-07 22:14:54

Chad Elstad
2019-09-07 22:24:28

Ben Lord
2019-09-07 22:27:04

原文網址 Chris Kramer
2019-09-07 21:39:17

If I place 2 models one inside the other (a hand and a sword) in the slicer will it print them together or would it be better to combine them in meshmixer??

翻譯年糕

Jarrod Smith
2019-09-07 21:42:45

Paul Soucy
2019-09-07 21:45:28

Caleb Custer
2019-09-07 21:49:13

James O'Keane
2019-09-07 21:49:32

Chris Kramer
2019-09-08 01:43:31

原文網址 Juli Forthewin
2019-09-07 21:02:23

What Voltage do the Fans run on? I dont want to start the printer until ive changed my Stepdown.

翻譯年糕

Spike Walker
2019-09-07 21:11:02

Jarrod Smith
2019-09-07 21:44:04

Silas Bo Nielsen
2019-09-07 23:46:10

Tiernan Messmer
2019-09-07 23:48:34

Dave Fishpig
2019-09-07 23:51:45

Juli Forthewin
2019-09-08 00:02:58

Juli Forthewin
2019-09-08 00:16:18

Silas Bo Nielsen
2019-09-08 06:04:12

Silas Bo Nielsen
2019-09-08 06:04:59

原文網址 John Adkins
2019-09-07 20:49:23

原文網址 James Vincent Paquette
2019-09-07 20:29:06

Just got my printer. Do I need to flash the latest firmware or should it be ok?

翻譯年糕

Nicolas A. Winton
2019-09-07 20:31:02

David McGyver
2019-09-07 20:37:17

Mike Tongue
2019-09-07 20:45:05

Mike McCreery
2019-09-07 20:58:35

Chad Elstad
2019-09-07 21:58:02

原文網址 John Jisha
2019-09-07 20:24:07

Had a fight with the software about setting my z=0, but after a firmware update this thing is pretty darn amazing so far

Edit: if any of y’all get the wierd “home first then z to bottom” message even though you’ve already “homed” I updated to V 4.2.2 and was able to successfully set my Z=0

翻譯年糕