Anycubic Photon Printer Owners 造訪社團

原文網址 Jake Cook
2019-09-06 00:21:14

What is the thickest lowest resolution layer height the photon can comfortably do? Looking to save time on a big piece

翻譯年糕

Paul Fagan
2019-09-06 00:22:33

Zena Andreou
2019-09-06 00:24:05

Mark Wardle
2019-09-06 00:24:29

Erik Pagan
2019-09-06 00:29:07

Jake Cook
2019-09-06 00:33:16

André Nettermann
2019-09-06 00:57:33

Alex Roughsedge
2019-09-06 05:01:05

Booga Kabuto
2019-09-06 09:41:22

Jarrod Smith
2019-09-06 10:04:00

Bob Deblier
2019-09-06 14:55:49

原文網址 Mike Guidry
2019-09-06 00:13:05

原文網址 Brandon Taylor
2019-09-06 00:08:17

Question on supports. I'm placing supports for 15-18mm scale human model. and there is an extremely tiny island at the back of the neck where the hair hangs down. The hair is short crop and it is the tip of one strand on a 15mm model to give you an idea how small were talking. Chitu wont let me place a support. The question is do I need to support it, and if yes how do I generate a support there?

翻譯年糕

Aaron Wiggins
2019-09-06 00:21:56

Ryan Miles Dika
2019-09-06 00:27:07

原文網址 John Smith
2019-09-06 00:05:44

It appears my Photon will be here tomorrow, time to finish the shopping list.

It appears that the resin (regardless of the Marketing Material says) is HAZMAT. So with any residue or cleaning solutions, just allow it to UV cure and then dispose?

翻譯年糕

Doug Clark
2019-09-06 00:10:12

Hugh Jeriolas
2019-09-06 00:15:38

Mike Roof
2019-09-06 00:24:03

John Smith
2019-09-06 12:08:05

原文網址 Gino Cruz
2019-09-05 23:25:17

hi everyone. this might have been asked before but here it is, can anyone point me to where i can download chitubox 1.5 profiles? i have it just recently installed and want to give it a try. i'm using monocure resins. thanks! :)

翻譯年糕

原文網址 Ofek Samsonov
2019-09-05 23:13:58

hi. in chitubox what exactly does each lift setting do distance speed and all that. if you got a link to explanation that would be great thanks

i have seen the user manual and its not specific enough. is lifting distance the initial lift distance before retraction or is it the total height of bottom layer from fep when build plate starts going down again.

翻譯年糕

Ofek Samsonov
2019-09-05 23:15:06

Ofek Samsonov
2019-09-05 23:18:56

Lamont Cutler
2019-12-31 12:55:56

原文網址 Isaac Jones
2019-09-05 22:33:43

Any ideas what caused this ?

First layers all stuck fine

Is it the weight of the supports should I make them medium ?

翻譯年糕

Ric Watts
2019-09-05 22:39:57

Gustaf Sjögren
2019-09-05 22:40:03

Ric Watts
2019-09-05 22:43:00

Isaac Jones
2019-09-05 22:43:36

Ric Watts
2019-09-05 22:44:12

Hugh Jeriolas
2019-09-05 22:59:04

Isaac Jones
2019-09-05 22:59:58

Hugh Jeriolas
2019-09-05 23:00:12

Hugh Jeriolas
2019-09-05 23:00:54

Jesse Mouré
2019-09-05 23:11:16

Hugh Jeriolas
2019-09-05 23:12:26

Gustaf Sjögren
2019-09-05 23:12:45

Isaac Jones
2019-09-05 23:15:38

Hugh Jeriolas
2019-09-05 23:18:33

Ric Watts
2019-09-05 23:58:07

Dallas Smith
2019-09-06 00:36:30

Thibaut Pral
2019-09-06 00:47:20

Dallas Smith
2019-09-06 00:48:57

Ric Watts
2019-09-06 00:52:21

Thibaut Pral
2019-09-06 00:55:23

Gustaf Sjögren
2019-09-06 01:53:13

David McGyver
2019-09-06 10:44:10

Isaac Jones
2019-09-06 16:05:16

Dallas Smith
2019-09-06 20:22:01

原文網址 Darren Wade
2019-09-05 22:30:54

Those that are heating their resin for Siriya Blu to keep it at 30C, what are you using to heat it? Are you heating the vat directly with something or are you usng an incubator style heater with a fan to heat the entire upper compartment? Do you do anything to cool the LCD?

翻譯年糕

Richard Burrell
2019-09-05 22:33:41

原文網址 Rob McEwen
2019-09-05 22:26:33

*RESOLVED* Reflashed FIRMWARE.

Damn. 2 months old and missing the front half of lcd now. Never had any leaks or screen lift or anything. Just out of the blue last night my print was only half the build plate. Is this an easy fix/check wiring? Or do i need to contact anycubic?

翻譯年糕