Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jake Cook
2019-09-06 08:41:34

First time to experience this. 2 issues. 1. The curl on the bottom of the steps. Usually I prevent this by printing at an angle and using supports which I did. 2. The delamination at the top of the print. The top of this wall section is splitting off.

The print was hollowed out with 3mm thick walls. 0.1 layer height with a 15 second dwell time on the cure. Anycubic grey resin.

翻譯年糕

Ryan Miles Dika
2019-09-06 08:44:41

Jake Cook
2019-09-06 08:45:12

Mark Wardle
2019-09-06 09:37:58

原文網址 Jake Cook
2019-09-06 00:21:14

What is the thickest lowest resolution layer height the photon can comfortably do? Looking to save time on a big piece

翻譯年糕

Paul Fagan
2019-09-06 00:22:33

Zena Andreou
2019-09-06 00:24:05

Mark Wardle
2019-09-06 00:24:29

Erik Pagan
2019-09-06 00:29:07

Jake Cook
2019-09-06 00:33:16

André Nettermann
2019-09-06 00:57:33

Alex Roughsedge
2019-09-06 05:01:05

Booga Kabuto
2019-09-06 09:41:22

Jarrod Smith
2019-09-06 10:04:00

Bob Deblier
2019-09-06 14:55:49

原文網址 Jake Cook
2019-08-16 02:08:46

Hey, i'm wanting to create very simple Nato wargaming counters to print and was curious as to a decent cad program for me to use for creating these? No cad experience here.

翻譯年糕

Mike Tongue
2019-08-16 02:22:28

Michael Kleinhenz
2019-08-16 18:05:43

原文網址 Jake Cook
2019-03-31 07:45:14

Print question. See pics, as you can see the top of this ship printed perfectly. This surface faced away from the build plate. The bottom is very rough and fluid looking. It faces the build plate and has supports on it. Any ideas how to improve this?

翻譯年糕

Matt Mason
2019-03-31 07:46:19

Shane Bui
2019-03-31 07:46:39

Peter Bolger
2019-03-31 07:48:13

Jake Cook
2019-03-31 07:52:18

Jake Cook
2019-03-31 07:57:02

Aaron Swickard
2019-03-31 08:03:23

David Marquis
2019-03-31 08:50:06

Sterling Osment
2019-03-31 13:54:48

Rob Baldwin
2019-03-31 14:58:09

Chad Elstad
2019-03-31 21:57:31

Oni Cron
2019-03-31 22:18:01

Jake Cook
2019-03-31 22:29:08

Oscar LP
2019-03-31 22:31:26

Terry Miller
2019-03-31 22:48:05

Richard Shapiro
2019-04-01 01:50:10

Jake Cook
2019-04-01 01:51:37

Richard Shapiro
2019-04-01 01:53:23

Jake Cook
2019-04-01 01:57:10

Rob Baldwin
2019-04-01 06:53:21

Craig Burrows
2019-04-01 10:52:36

原文網址 Jake Cook
2019-03-29 20:50:49

With my FDM printer, the slicer software had a way to make the objects hollow and use a fill setting. Is there a way to do that with the Photon slicer? If not, what software would you use?

翻譯年糕

Alexander Thordendal
2019-03-29 20:56:24

Fred Steinmann
2019-03-29 20:57:06

Robb Nunya
2019-03-29 21:09:00

Norbert Kupeczki
2019-03-29 21:22:29

Kory Sebby
2019-03-29 22:06:41

Jake Cook
2019-03-29 22:15:22

Björn Ståhlnacke
2019-03-29 22:24:45

Jake Cook
2019-03-29 23:47:54

Stefan Giudici
2019-03-30 00:17:32

Mark Wardle
2019-03-30 00:23:09

原文網址 Jake Cook
2019-03-19 01:22:39

New user with some questions about after print maintenance. So do you need to drain and filter the vat after every print or if you wont be using it a while? What would say is your after print routine?

翻譯年糕

Rob Mayberry
2019-03-19 01:24:46