Anycubic Photon Printer Owners 造訪社團

原文網址 Peter Lynn
2019-07-25 17:15:05

Any recommendations on ebay for a ultrasonic cleaner.

Does monocure resinaway have a strong smell to it.

翻譯年糕

Tim Perry
2019-07-25 17:45:15

Eivind Husby
2019-07-25 18:39:34

Eivind Husby
2019-07-25 18:43:46

Tim Perry
2019-07-25 19:02:24

Eivind Husby
2019-07-25 19:03:40

原文網址 Clint Maiuri
2019-07-25 17:10:55

Hey guys just curious on how many have used clear resin and how well does it turn out ?
Cheers Hey guys just curious on how many have used clear resin and how well does it turn out ?
Cheers 翻譯年糕

Eivind Husby
2019-07-25 17:34:19

Clint Maiuri
2019-07-25 17:37:43

Bob Heron
2019-07-25 17:44:11

Eivind Husby
2019-07-25 17:54:29

Eivind Husby
2019-07-25 17:55:56

Clint Maiuri
2019-07-25 18:16:35

Eivind Husby
2019-07-25 18:18:35

Clint Maiuri
2019-07-25 18:19:43

Ines Silva
2019-07-25 18:37:16

Bob Heron
2019-07-25 18:57:04

Greg Chapman
2019-07-25 19:49:19

Scott Pavlich
2019-07-25 20:35:06

Thomas Weissböck
2019-07-26 02:16:21

Shane Graber
2019-07-27 22:01:41

Greg Chapman
2019-07-28 03:33:51

原文網址 Adam Wiseman
2019-07-25 16:48:03

I've been using the monocure rapid clear to print miniatures, but because it's so clear it can be tough to see the details before priming them. Has anyone got any suggestions on good alternatives?

翻譯年糕

Klaus Teschner
2019-07-25 16:53:26

Greg Chapman
2019-07-25 17:07:23

Scott Pavlich
2019-07-25 21:48:22

Mike Foreman
2019-07-25 23:26:06

Clifford Schwankner
2019-07-26 05:16:06

原文網址 Iñigo Sordo
2019-07-25 16:16:11

Well, custom usb drive enclosure for a friend designed in Fusion 360. Board fits like a glove. Perfect fit. Quite sad about the support side of the part. Would love to hear some advices about supports from the gurus because no doubt its my dark zone in resin printing. Printed in Elegoo Grey, 11 secs, 8 bottom layers at 70 secs, four hours.

翻譯年糕

Claus Hingebjerg
2019-07-25 17:00:53

Iñigo Sordo
2019-07-25 17:27:31

Simon Stewart
2019-07-25 17:52:33

Iñigo Sordo
2019-07-25 18:05:44

Simon Stewart
2019-07-25 18:16:06

Justin Cupitt
2019-07-25 19:26:51

Stephen Carr
2019-07-25 19:49:40

Tim Moulton
2019-07-25 23:59:56

AJ Soulstice
2019-07-26 02:14:46

David Nicholls
2019-07-26 02:23:43

Paul West
2019-07-26 02:33:58

原文網址 Goga Pop Georgievski
2019-07-25 16:04:40

So, the first time FEP changes. I noticed a loss in detail and some fail in the prints. I thought it was bad cleaning, as most problems come from this, but I started to print. Due to small cracks I got a resin leak on the screen, but not much. I had a Kapton on the edges of the screen, following the instructions of the guys. I followed the Anycubic video manual for FEP changes, taking a good look at the tension, listening to the pitch and feeling with fingers. I changed the FEP after 180 miniatures - 1L body resin passed. My printer is great again for printing.

Cleaning resin on the screen.

1. Do not be nervous

2. Clear the screen well with IPA

3. Soak them and put them in the area

4. Gently use a spatula (without sharp edges) to scrape the remains of cured resin on the screen. I had to soak 5 times and scratching above the soaked wipe avoiding scratches. Be patient. Dont put too much pressure wile scraping.
Hope this helps to you all.
In my case, after all this, no re-calibration was needed.

翻譯年糕

Drew Teichman
2019-07-25 16:12:19

Bob Deblier
2019-07-25 16:30:54

Scott Pavlich
2019-07-25 19:25:16

原文網址 Silvio Pelosi
2019-07-25 15:37:58

not bad as a first job !! perfect !! can you tell me if I can mix the resins (green-transparent) and how long should I leave the pieces in the alcohol ?? thank you guys

翻譯年糕

Bob Deblier
2019-07-25 16:53:42

Bob Deblier
2019-07-25 16:54:59

Silvio Pelosi
2019-07-25 16:58:23

Bob Deblier
2019-07-25 17:00:14

Silvio Pelosi
2019-07-25 17:05:11

Bob Deblier
2019-07-25 20:27:35

Silvio Pelosi
2019-07-25 22:11:32

Bob Deblier
2019-07-25 22:14:21

Phil Hays
2019-07-26 11:20:58

原文網址 Amy Liao
2019-07-25 15:35:30

20% off for Photon-S, it's a flash deal!!!

Will end within two hours, caught it. ? ?

? ? https://www.amazon.de/dp/B07PYVLN82

翻譯年糕

Marcus Stübe
2019-07-26 02:22:56

Patrick Morgan
2019-07-26 03:12:41

Marcus Stübe
2019-07-26 03:22:56

Patrick Morgan
2019-07-26 03:24:24

Tomas Salo
2019-07-26 15:39:10

原文網址 Niclas Hokuspokus
2019-07-25 15:09:48

Hey,

is there any possibility that the printsurface lifts higher between every layer? I want to print with a high viscous resin and the cap between the printsurface and the FEP film ist so small.

Thanks!

翻譯年糕

Amy Baldwin
2019-07-25 15:41:57