Anycubic Photon Printer Owners 造訪社團

原文網址 Benjamin Tan
2019-07-10 09:52:46

Michael J Morris
2019-07-10 09:55:09

Benjamin Tan
2019-07-10 09:58:24

Lucas Miguel
2019-07-10 10:00:02

Benjamin Tan
2019-07-10 10:03:20

Brad Morris
2019-07-10 10:14:42

Benjamin Tan
2019-07-10 10:18:22

Brad Morris
2019-07-10 10:19:21

Christian Sargent
2019-07-10 10:22:00

Benjamin Tan
2019-07-10 10:25:25

Christian Sargent
2019-07-10 10:26:41

Eric Wilfreesboro
2019-07-10 10:30:08

Christian Sargent
2019-07-10 10:31:23

Joe Broggio
2019-07-10 16:34:37

Andi Gordon
2019-07-10 16:40:41

Benjamin Tan
2019-07-10 17:40:48

Fred Bey
2019-07-12 10:33:42

原文網址 Sonny Green
2019-07-10 09:26:30

I have my idiot newbie question of the day....

How long is it OK to leave a print in the printer after it's done before removing it? For instance, if I start a print which will take 4 hours and don't get back to the printer until 12 hours later would it still be OK for normal post-processing?

翻譯年糕

Jay Kay
2019-07-10 09:27:37

Sonny Green
2019-07-10 09:27:50

Chad Elstad
2019-07-10 09:30:48

Sonny Green
2019-07-10 09:34:03

Darren Donovan
2019-07-10 09:34:48

David McGyver
2019-07-10 12:53:55

原文網址 Yamil Hugo Corco
2019-07-10 09:11:42

Hola grupo que hacen =)

翻譯年糕

原文網址 Jeremy Jury
2019-07-10 09:04:31

Thank you for all the information! Making the 2nd print come out pretty good

翻譯年糕

原文網址 Adam Musgrove
2019-07-10 08:59:54

So this happened today. Not sure what to make of it so I will ask the hive mind. Long story short, I had a leak in a new FEP I put on the other day. Resin had leaked out and over about 1/3 of my LCD screen. Lucky for me I had taped up the sides of the screen so nothing leaked into the innards of the printer. It also leaked while nothing was printing, so no resin really cured anywhere. After cleaning everything off carefully and setting my zero lvl again, I ran a test on the UV light and got this. My pattern now has a "mole" in the top right. Not sure if it just appeared or if its been there a while.

My question is have yall seen weird little dead spots like this before? I am going to assume this will jack with any future prints until I get it fixed. What do you think my options are with this?

翻譯年糕

Dominick Trascritti
2019-07-10 09:10:21

Will Koehler
2019-07-10 09:28:15

原文網址 Chorng Swc
2019-07-10 08:58:21

Anyone know if anycubic green UV resin contain sulfur?

翻譯年糕

Stefan Giudici
2019-07-10 09:00:37

Chorng Swc
2019-07-10 09:11:19

Stefan Giudici
2019-07-10 10:18:35

Chorng Swc
2019-07-10 11:23:46

Lane Shutt
2019-07-10 16:04:24

Chorng Swc
2019-07-10 22:49:52

Tom Smith
2019-07-10 23:48:12

Chorng Swc
2019-07-11 08:42:32

原文網址 Rich Newman
2019-07-10 08:57:31

So what are some good clear coats to spray over resin parts to make them able to grind against each other? (Like or action figures joints, etc.)

Ideally there would be something that formed a thin layer but was still "tough"???

翻譯年糕

Chayanin Somton
2019-07-10 16:31:03

原文網址 Juan Chavez
2019-07-10 08:51:29

Finally ran into the z wobble issue. Any suggestions to prevent this issue? Thanks!

翻譯年糕

Jarrod Smith
2019-07-10 08:53:03

Juan Chavez
2019-07-10 08:55:19

Jeff Wand
2019-07-10 08:56:17

Juan Chavez
2019-07-10 08:59:45

Kyle Turgoose
2019-07-10 09:02:26

Sean O'Hayer
2019-07-10 09:06:21

Juan Chavez
2019-07-10 09:17:17

Juan Chavez
2019-07-10 09:18:09

Scott Pavlich
2019-07-10 09:19:34

Joe Broggio
2019-07-10 09:23:02

Juan Chavez
2019-07-10 09:23:27

Joe Broggio
2019-07-10 09:24:00

Joe Broggio
2019-07-10 09:25:27

Juan Chavez
2019-07-10 09:27:13

Joe Broggio
2019-07-10 09:28:32

Joe Broggio
2019-07-10 09:30:16

Juan Chavez
2019-07-10 09:32:36

Noah Lothes
2019-07-10 09:32:48

Sean O'Hayer
2019-07-10 09:33:29

Juan Chavez
2019-07-10 09:43:35

Sean O'Hayer
2019-07-10 09:46:35

Juan Chavez
2019-07-10 09:48:15

Sean O'Hayer
2019-07-10 09:56:12

Jeff Wand
2019-07-10 10:02:45

Juan Chavez
2019-07-10 10:04:53

Luke Mason
2019-07-10 11:05:42

Bob Deblier
2019-07-10 14:27:32

Jeff Wand
2019-07-10 14:31:31

Zäta Doe
2019-07-10 14:35:09

Kamil Bartosz Bilski
2019-07-10 16:16:55

Ricardo Moleda
2019-07-10 21:09:16

Noah Lothes
2019-07-10 22:34:48

原文網址 Peter Hill
2019-07-10 08:38:30

Has anyone got tips for Anycubic orange? There's only one listing on the spreadsheet for it. 2 prints using them have peeled off the plate. The last one I did increased the bottom Exposure to 120 and still no luck.

翻譯年糕

Trevor McIntosh
2019-07-10 08:52:31