Anycubic Photon Printer Owners 造訪社團

原文網址 Daniel McCarthy
2019-07-09 20:46:20

Help please! First print of the test model was great but since I’ve had no luck with the resin completely failing to adhere to the plate (instead stuck to fep.) I’ve since re levelled the plate and done resaved several iterations of the model. About 4 fails so far. Any ideas why this could be happening? I’m a bit bewildered considering the test cane out perfectly and I’m using the same settings and resin type ?

翻譯年糕

Bob Deblier
2019-07-09 20:48:24

Kevin Lems
2019-07-09 20:50:16

Daniel McCarthy
2019-07-09 21:47:26

Daniel McCarthy
2019-07-09 21:48:57

原文網址 Jonathan Lopera
2019-07-09 20:15:33

Best practices for large lithophanes? My models are coming out slightly wavy, and when paused alignment shifts making a line... Best practices for large lithophanes? My models are coming out slightly wavy, and when paused alignment shifts making a line... 翻譯年糕

Jeff Schaber
2019-07-09 20:23:08

Jonathan Lopera
2019-07-09 22:13:01

Jonathan Lopera
2019-07-09 22:14:10

Jonathan Lopera
2019-07-09 22:14:24

Jeff Schaber
2019-07-09 23:54:58

原文網址 David Hewis
2019-07-09 19:29:40

My Photron has just arrived, I went for the Photron instead of the Photron S as Amazon is selling it with £100 off for the next two days :) the good news is everything is setup and ready to print once it's installed in it's printing place. The bad news is the IPA I ordered won't get her till Saturday......No...that's to long a wait , so ordered some on next day delivery so printing can start tomorrow :) and thanks for accepting my request to join the group.

翻譯年糕

Greg Chapman
2019-07-09 19:33:28

David Hewis
2019-07-09 19:35:10

Pat Sinclair
2019-07-09 19:35:35

Sterling Murphy
2019-07-09 19:48:32

Dawkins Alejandro Ricardo
2019-07-09 20:06:10

David Hewis
2019-07-09 20:07:51

Morten Simonsen
2019-07-09 20:11:09

Will Koehler
2019-07-09 20:24:42

Dawkins Alejandro Ricardo
2019-07-09 20:31:12

David Hewis
2019-07-09 20:33:15

Nemo Vilpponen
2019-07-09 23:29:09

Erin Fezell
2019-07-10 01:39:53

Sterling Murphy
2019-07-10 01:40:58

Jaco Norchie Nortje
2019-07-10 03:19:26

原文網址 Cliff Goodwin
2019-07-09 19:28:50

Hey group!

Well, I took in everything you all had to say. I did not get to take her off the build plate this morning but there are 2 arms!!!!!!

翻譯年糕

Daniel Särnblom
2019-07-09 20:13:45

Cliff Goodwin
2019-07-09 20:42:17

Cliff Goodwin
2019-07-09 22:08:23

Phillip Stokes
2019-07-10 09:31:44

Ian Fiebig
2019-07-11 01:37:43

原文網址 Peter Boardman
2019-07-09 19:23:36

Now I’m getting somewhere!

0.02mm, Prima Creator Value resin

翻譯年糕

Jeremy Gilbert
2019-07-09 22:09:24

Jeremy Gilbert
2019-07-09 22:09:28

Shane Johnson
2019-07-10 14:26:42

Kamil Bartosz Bilski
2019-07-10 18:38:12

Thomas Glover
2019-08-19 20:27:29

原文網址 Mike Allen Jr.
2019-07-09 19:10:02

I guess this is a successful print?

翻譯年糕

原文網址 Andrew Fudge
2019-07-09 18:56:34

Sometimes supports seem to bleed into the modle and then leave some pretty seriuos damage when removed. I'm not talking about at the contact points, but down the length. In the render in Chitubox it looks as though there's no contact between the model and support (other than where there should be) but after printing they've almost blended together. Any fixes for this?

翻譯年糕

Chad Elstad
2019-07-09 20:06:58