Anycubic Photon Printer Owners 造訪社團

原文網址 Scott Simoneau
2019-04-16 08:02:37

Had my first real "failed" print today after one week of 95% successes.

So I was printing eight more or less identical figures. Settings that I've used successfully on this set of figures a couple times already.

The four on the left side of the build plate ended up half-printed, and everything except the supports was stuck in the vat. The four on the right side of the build plate printed off just fine.

There were two new variables in this print: I went from printing 7 at a time, to 8 at a time, and I went from using green to orange resin.

I've cleaned out the vat. Do I need to relevel? Anything else I need to do other than try again?

翻譯年糕

Danny Lloyd
2019-04-16 08:06:04

Michael Van Kesteren
2019-04-16 08:22:03

原文網址 Scott Simoneau
2019-04-16 07:58:17

So I know about the spreadsheet with recommend settings and all that, but I'm curious as to what the settings actually mean.

Layer thickness: Does a smaller thickness = more detail? And presumably a smaller thickness = longer print time?

Normal exposure time: This is the time the light from the screen is displaying? So the larger the thickness, the longer this should be? And presumably also a longer time = longer print time. Is there any benefit to raising this, or should I aim to keep it as short as the print will allow?

Bottom Layers/Bottom Exposure Time: What exactly does this do for the print? What is the advantage to more bottom layers?

Light-off Delay: Is this the time the LCD is not displaying? Would this be before or after the printer raises the Z axis? What impact does this have on the print?

翻譯年糕

Mike Nellis
2019-04-16 08:01:43

Mike Nellis
2019-04-16 08:02:24

Dustin Skye
2019-04-16 08:07:59

Wes Swain
2019-04-16 08:12:52

Neil Ramsay
2019-04-16 09:07:11

Chris Visser
2019-04-16 10:43:40

Dustin Skye
2019-04-16 10:52:57

Dustin Skye
2019-04-16 10:55:08

Chris Visser
2019-04-16 11:00:47

原文網址 Filipp Filipp
2019-04-16 07:07:46

Robot first print on anycubic! Solid one
adhesive was too much so the part of plate sticked to a resin is this normal?

翻譯年糕

Ryan Frazier
2019-04-16 07:29:16

Luke Mason
2019-04-16 13:25:18

Dan Smith
2019-04-16 16:39:53

原文網址 Jozef Orenič
2019-04-16 06:39:27

What do you think guys? What is better placement? I think if angle 45deg is really needed in so flat models? (it's litophane model from a picture)

翻譯年糕

伟洪
2019-04-16 07:00:33

Philippe Maegerman
2019-04-16 12:36:27

Jozef Orenič
2019-04-16 13:27:20

William David Cunningham
2019-04-17 06:03:55

Jozef Orenič
2019-04-17 06:06:34

William David Cunningham
2019-04-17 06:20:18

Jozef Orenič
2019-04-17 15:12:43

原文網址 Philip M Ferreira
2019-04-16 06:04:18

Hello guys
What better way to remove the brackets without leaving the mark holes?

翻譯年糕

Art Barrow
2019-04-16 06:10:12

Chad Elstad
2019-04-16 06:20:00

Michael Hull
2019-04-16 06:24:41

Jordan Baldrige
2019-04-16 06:25:25

Jordan Baldrige
2019-04-16 06:26:43

Philip M Ferreira
2019-04-16 06:32:52

Sen Kun
2019-04-16 12:04:15

David Nicholls
2019-04-16 16:13:45

原文網址 Alex Martin
2019-04-16 05:47:23

Photon S came in on Saturday and got my first print off within a few hours

翻譯年糕

Robert Thorhauer
2019-04-16 06:05:57

Alex Martin
2019-04-16 06:08:47

Yussuf Al-sagh
2019-04-16 06:08:49

Mitchell King
2019-04-16 06:15:56

Alex Martin
2019-04-16 06:31:19

Alex Martin
2019-04-16 06:33:38

Jonathan Hall
2019-04-16 06:35:31

Alex Martin
2019-04-16 06:48:53

Jon Tallon
2019-04-16 07:35:26

Hugo Mak
2019-04-16 07:38:08

Tyler Garland
2019-04-16 07:41:23

Michal Powierza
2019-04-16 07:50:57

Tomasz Dudziak
2019-04-16 07:51:47

Nathaniel Zhu
2019-04-16 07:55:53

Jon Tallon
2019-04-16 08:12:33

Danny Lloyd
2019-04-16 08:16:41

Danny Lloyd
2019-04-16 08:17:30

Danny Lloyd
2019-04-16 08:17:48

Nathaniel Zhu
2019-04-16 08:19:07

Nathaniel Zhu
2019-04-16 08:22:01

Olivier Clément
2019-04-16 08:44:42

Muhammad Zulkhairol Yacob
2019-04-16 09:33:35

Kyle Turgoose
2019-04-16 10:04:09

Sen Kun
2019-04-16 11:10:47

Jeremy Wolff
2019-04-16 11:57:34

Nathaniel Zhu
2019-04-16 12:03:01

Alessandro Iannacci
2019-04-16 15:52:34

Jamie Joules
2019-04-16 15:55:31

Vidal Sanchez
2019-04-16 21:00:37

Naumann Alex
2019-04-18 19:09:33

Naumann Alex
2019-04-18 19:11:23

Jamie Joules
2019-04-18 19:12:09

Jamie Joules
2019-04-18 19:22:51

Lawrence Heyda
2019-04-20 02:13:57

Jeremy Wolff
2019-04-20 03:02:08

Lawrence Heyda
2019-04-21 03:18:18

Lawrence Heyda
2019-04-21 03:29:44

Jeremy Wolff
2019-04-21 04:13:46

原文網址 Nick Cassar
2019-04-16 05:24:12

What are reasons the print isn’t sticking to the bed? I changed my FEP yesterday. And I clean after every print. Was perfect and now nothing sticks

翻譯年糕

Gon Garcia
2019-04-16 05:26:21

Juan Camilo Herrera
2019-04-16 05:29:16

Nizhen Phang
2019-04-16 05:35:53

Nick Cassar
2019-04-16 06:10:51

Nick Cassar
2019-04-16 06:11:36

Nick Cassar
2019-04-16 06:12:02

Joel Clarke
2019-04-16 06:36:11

Nick Cassar
2019-04-16 07:02:09

Tori Beckett
2019-04-16 07:20:49

Sen Kun
2019-04-16 11:53:48

Joel Clarke
2019-04-16 12:51:40

Nick Cassar
2019-04-16 18:12:48

Nick Cassar
2019-04-16 18:15:37

Justin Cottom
2019-04-17 00:59:49

原文網址 Carsten Degenhardt
2019-04-16 05:14:38

Has somebody else experienced that an USB stick is not recognized by Windows 10 after you printed with the photon? Right now I always have to reboot my laptop for it to work again. Most solutions I found require you to reboot the laptop and that gets annoying

翻譯年糕

Dan Hjulberg
2019-04-16 05:17:47

Chad Elstad
2019-04-16 05:21:34

Carsten Degenhardt
2019-04-16 05:40:13

Jethro Pugh
2019-04-16 08:13:38

Carsten Degenhardt
2019-04-16 08:48:18

原文網址 Hamza Doğan
2019-04-16 04:21:29

Hello, i've just finished my first print and i am not satisfied with the results. Settings are preloaded software settings on the native slicer. There is obvious ringing. Is it normal or my unit is faulty? Appreciate if you help me.

翻譯年糕