Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Justin Cottom
2020-02-21 08:52:57

Anyone know what could cause this? Same settings I’ve always used, new bottle of resin that I’d used just previously. Two models printed out fine in this batch but the rest stuck to the bottom. Time to change the fep?

翻譯年糕

Ivan Adhi R
2020-02-21 08:57:41

Penn Davies
2020-02-21 08:58:14

Arthur White
2020-02-21 12:05:25

原文網址 Justin Cottom
2019-10-22 23:08:38

After countless perfect prints my Photon isn't working correctly. Now the plate stops moving up and down after the first quarter to half inch of the print is printed. Has anyone else had this happen? At first I thought that maybe the resin was bad or something, but I tried again with new resin and it's still doing it. Next I might see if it's a firmware problem or maybe the USB. Anybody have any ideas?

翻譯年糕

Dan Hjulberg
2019-10-22 23:12:53

Jim Stephens
2019-10-22 23:26:48

原文網址 Justin Cottom
2019-04-23 05:41:12

Do you clip off the supports before or after curing? I had some pieces snap off while snipping the supports after curing because it was too brittle.

翻譯年糕

Chris Comeau
2019-04-23 05:46:50

James Cachia-Garrett
2019-04-23 05:49:01

Phillip Stokes
2019-04-23 05:52:46

Derek Lamar
2019-04-23 05:57:26

Phillip Stokes
2019-04-23 05:59:45

Jacques Abbeels
2019-04-23 06:00:57

Richard Shapiro
2019-04-23 06:03:47

原文網址 Justin Cottom
2019-04-18 23:47:16

So close to finally getting a good print. Printed more than just the supports this time, but I have no idea what is up with the resin that comes off to the left and right of the print. Has this happened to anyone else?

翻譯年糕

Dennis Back
2019-04-18 23:51:51

Aaron C Plante
2019-04-19 00:06:02

Joseph Bushen
2019-04-19 00:06:17

Guajolote Messias
2019-04-19 00:20:59

Ty Mansfield
2019-04-19 01:36:18

Richard Shapiro
2019-04-19 06:42:02

Valentino Vettoretti
2019-04-19 06:51:34

Dan Smith
2019-04-19 07:12:27

Justin Cottom
2019-04-20 02:50:41

原文網址 Justin Cottom
2019-04-18 11:12:11

Test print number 10? At least I got something. I’m not sure what the problem is. I’ve leveled it so many times. Once I was able to print only the supports, which is the closest to an actual print I’ve got. I’ve attached pictures of the settings, slice, and what printed. Anyone have any ideas?

翻譯年糕

Stefan Giudici
2019-04-18 11:22:12

Dennis Back
2019-04-18 11:29:39

Hector Felix
2019-04-18 11:31:42

Marnie Jefferson
2019-04-18 11:34:53

Justin Cottom
2019-04-18 11:45:11

原文網址 Justin Cottom
2019-04-16 13:08:49

After a week of owning an Anycubic Photon and numerous failed prints, this is the best print I got and it’s nothing like how the mini should have turned out. Has anyone had this issue or might know how to fix this?

翻譯年糕