Anycubic Photon Printer Owners 造訪社團

原文網址 Tomasz Kańka
2019-03-10 17:51:27

This is how prints look under electron microscope. Two samples one, printed horizontally and one vertical. Rezin: Anycubic green 0.05 mm 16s exposures.
(I think, I overexposed it :p )

翻譯年糕

Sen Kun
2019-03-10 18:17:43

Michael Tennent
2019-03-10 20:52:11

Sébastien Guilbaud
2019-03-10 21:38:56

Sen Kun
2019-03-10 21:47:23

原文網址 Marshall Tearle
2019-03-10 17:33:49

Can confirm that replacing the 2K screen is pretty straightforward if you're careful with the thin ribbon cable. Printing again.

翻譯年糕

原文網址 Joschka Röben
2019-03-10 17:03:41

Automotive hood ornaments coming out of the Photon. All printed without supports, as they ruin all the surfaces they attach to...

翻譯年糕

John Bubuz
2019-03-10 18:44:35

Joschka Röben
2019-03-10 19:00:05

Chris Kölsch
2019-03-10 22:48:02

Joschka Röben
2019-03-10 23:20:17

Micah Vestal
2019-03-11 04:11:48

Joschka Röben
2019-03-11 04:15:15

原文網址 Guillaume Douchet
2019-03-10 16:38:37

hello, I have not lit my photon for 3 months and it does not work anymore.
The uv runs 1 hour and after it does not show anything: /
Someone knows why ?

翻譯年糕

Guillaume Douchet
2019-03-12 18:02:14

Sen Kun
2019-03-12 18:14:04

Guillaume Douchet
2019-03-12 18:16:02

Sen Kun
2019-03-12 18:17:07

Guillaume Douchet
2019-03-12 18:18:27

Guillaume Douchet
2019-03-12 18:30:21

Sen Kun
2019-03-12 18:32:05

Guillaume Douchet
2019-03-12 18:35:03

Sen Kun
2019-03-12 18:35:07

Sen Kun
2019-03-12 18:36:07

Sen Kun
2019-03-12 18:37:50

Guillaume Douchet
2019-03-12 18:39:55

Guillaume Douchet
2019-03-12 19:11:44

Jeff Lee
2019-03-12 19:13:36

Guillaume Douchet
2019-03-12 19:25:15

Jeff Lee
2019-03-12 20:24:06

Guillaume Douchet
2019-03-12 20:42:05

Jeff Lee
2019-03-12 21:13:52

原文網址 Andrew McKay
2019-03-10 14:31:35

Hi, I’m trying to print miniatures using Anycubic grey mixed with 20% Monocure Flex. I know a few people have tried this before, does anyone have any setting to suggest? Any kind of starting place would be really helpful, thanks!

翻譯年糕

Stefan Giudici
2019-03-10 14:32:39

Andrew McKay
2019-03-10 14:33:50

Rachel Woolford
2019-03-10 14:40:06

Vladimir Strycek
2019-03-10 14:45:24

Stefan Giudici
2019-03-10 15:12:01

Stefan Giudici
2019-03-10 15:12:10

Stefan Giudici
2019-03-10 15:13:08

Andrew McKay
2019-03-11 00:39:37

原文網址 Titan Ross
2019-03-10 14:26:01

I waited 15hrs for these pieces to print at 0.01and for some reason these two pieces dident even print at all, nothing on the plate and nothing in the vat ?‍♂️ ?‍♂️ what went wrong?

翻譯年糕

Dan Smith
2019-03-10 14:27:25

Juan Camilo Herrera
2019-03-10 14:30:35

Stefan Giudici
2019-03-10 14:33:00

Titan Ross
2019-03-10 14:36:24

Juan Camilo Herrera
2019-03-10 14:36:54

Titan Ross
2019-03-10 14:38:00

Dan Smith
2019-03-10 14:40:42

Fred Breton
2019-03-10 14:47:25

Jaco Norchie Nortje
2019-03-10 15:01:00

Titan Ross
2019-03-10 15:01:39

Christian Plösser
2019-03-10 15:38:46

Titan Ross
2019-03-10 15:43:37

Gergely Dömölki
2019-03-10 16:24:25

Puren Bulat
2019-03-11 23:07:59

Salvador Perejón Moreno
2019-03-12 06:28:35

原文網址 Fred Breton
2019-03-10 13:57:24

Latest Duncan Louca's Minotaur, always done with monocure rapid clear.

翻譯年糕

原文網址 Michael M Thompson
2019-03-10 12:37:50

Now to do a different color and mix/match.

Spinney rings.

Dummy UV LED setup for attention ? ? ?

翻譯年糕

原文網址 Tim Allen
2019-03-10 10:54:21

Musk Ox APC from the Antenocitis Workshop stl kickstarter. 28mm figure for scale. Printed with Sparkmaker LCD-T clear (primed white in photos), 0.04mm layers at 12 sec per normal layer. The hull and tracks took over 16 hours each. The hull had a slight shift to one side about 1/5 of the way through the print but it's barely noticeable. The rear of the model has some goopy details as seems typical of clear resin towards the build plate, but it's better than Photocentric3D Firm. I think this model will make a good Razorback after I compress the length a bit.

翻譯年糕

David Challoner
2019-03-10 15:33:02

John Bubuz
2019-03-12 23:40:16

原文網址 Michael Earley
2019-03-10 10:09:53

Printer is making a bit of a screeching sound like it needs lube on the z Axis.

What sort of lube/grease should I use on it? What was it shipped with? Figure I’ll roll out to Home Depot tomorrow. Printer is making a bit of a screeching sound like it needs lube on the z Axis.

What sort of lube/grease should I use on it? What was it shipped with? Figure I’ll roll out to Home Depot tomorrow. 翻譯年糕

Michael Earley
2019-03-10 10:11:50