Anycubic Photon Printer Owners 造訪社團

原文網址 Guy Whiteing
2019-02-17 08:13:00

My first proper design from solidworks. Instead of just downloading from thingiverse, any suggestions on how to allow for slight expansion in size? Just keep running tests of set sizes?

翻譯年糕

Stephen Arsenault
2019-02-17 08:22:26

Guy Whiteing
2019-02-17 08:23:32

Stephen Arsenault
2019-02-17 08:25:50

Sebastian Finke
2019-02-17 08:51:02

Guy Whiteing
2019-02-17 08:53:45

Sebastian Finke
2019-02-17 08:56:02

Guy Whiteing
2019-02-17 09:03:00

Sebastian Finke
2019-02-17 09:07:42

John Boyington
2019-02-17 11:14:21

John Boyington
2019-02-17 11:18:13

Vinicius Silva
2019-02-17 12:04:31

Darron Rodrigues
2019-02-17 17:45:11

Guy Whiteing
2019-02-17 18:00:43

原文網址 Michael M Thompson
2019-02-17 07:49:12

Trying to cure at night. Need to make my box.

翻譯年糕

Scott Young
2019-02-17 13:55:09

Michael M Thompson
2019-02-17 14:14:06

原文網址 Dave Williams
2019-02-17 06:02:02

Printed some 10mm figures for a 1/350 battleship

翻譯年糕

Kevin Boogaard
2019-02-17 06:55:48

Dave Williams
2019-02-18 04:20:32

原文網址 Jason Saiter
2019-02-17 05:58:13

Printing well despite the lifting from the bed.

翻譯年糕

Dawkins Alejandro Ricardo
2019-02-17 06:03:51

Jason Saiter
2019-02-17 06:05:18

Tom Sargison
2019-02-17 06:47:59

Dawkins Alejandro Ricardo
2019-02-17 07:21:27

Jason Saiter
2019-02-17 07:30:39

Dawkins Alejandro Ricardo
2019-02-17 07:31:17

Jason Saiter
2019-02-17 07:32:04

Jason Saiter
2019-02-17 07:32:45

Joe Broggio
2019-02-17 12:26:28

Jason Saiter
2019-02-17 12:53:14

原文網址 Robert Silvers
2019-02-17 05:02:57

Another thick / high polymer content resin. Works on Photon at 20s exposure.

翻譯年糕

Hobby Mike
2019-02-17 05:12:34

Ettore Maria Bar
2019-02-17 16:43:26

Mark Peng
2019-02-17 21:39:56

Dustin Skye
2019-02-17 22:56:56

Mark Peng
2019-02-18 10:27:13

Vinicius Silva
2019-02-18 18:57:43

Paul Mendoza
2019-02-19 05:50:20

Mark Peng
2019-02-19 06:11:16

Mark Peng
2019-02-19 06:33:30

Mark Peng
2019-02-22 23:18:57

原文網址 James Anderton
2019-02-17 04:44:19

Im going to printing a few small figures and was planning on painting them, am I best priming them? If so what brands do folks recommend for priming and also painting ?

Will be printing in Anycubic clear resin btw.

翻譯年糕

David Nicholls
2019-02-17 04:53:49

Sercan Güzel
2019-02-17 04:55:01

James Anderton
2019-02-17 04:55:03

David Nicholls
2019-02-17 04:56:42

David Nicholls
2019-02-17 04:57:31

Sercan Güzel
2019-02-17 04:58:21

Marcus Leander
2019-02-17 05:03:28

Joey Pruitt
2019-02-17 05:06:24

David Nicholls
2019-02-17 06:13:36

Ray Santiago
2019-02-19 19:14:41

Marcus Leander
2019-02-19 19:17:06

Ray Santiago
2019-02-19 19:18:10

原文網址 Yelena Novikova
2019-02-17 04:43:25

Looks like my vision failed me and I overfilled the vat this time and now resin is over the screws and in the bearings. Anyone had this accident before and did you just submerge into IPA to thoroughly clean and dry and never had other problems? Or does it mean I now need this entire part replaced?

翻譯年糕

Richard Shapiro
2019-02-17 04:46:38

原文網址 Carla Birch
2019-02-17 04:31:09

Maybe someone might be able to help out with this small problem, i just printed direct on the build platform for the first time, mostly because i need a total flat underside and to save on time. But i seem to be getting like a extra 1mm or so of the very first layer. See how its got like 1mm before it gets to the chamfer, where it should start the chamfer right away.

I'm using the photon slicer and 0.025 with 12sec exp and 8 bottom layers at 60sec using anycubic translucent yellow.

翻譯年糕

Anthony Pham
2019-02-17 04:35:24

原文網址 Darryl Kerbow
2019-02-17 04:04:05

I have been printing with my AnyCubic Photon for about a week now, and it’s been printing very nicely. However the past few days I have been running into an issue. When I plug my stick into the usb port in it just flashes and does not read the files to print. The touch screen responsiveness has also slowed down while the the memory stick is in the reader. When the memory stick is plugged into the desktop it works fine. Has my memory stick gone bad, or is this just a sign of something more ominous? Set up is bone stock and I am still using the initial bottle of resin that came with the printer.

翻譯年糕

Mark Wardle
2019-02-17 04:05:54

Richard Shapiro
2019-02-17 04:06:08

Mark Wardle
2019-02-17 04:07:22

Darryl Kerbow
2019-02-17 06:16:55

Ad Versteeg
2019-02-19 00:05:06

原文網址 Mark Wardle
2019-02-17 04:03:59

That time of the week again. this video is aimed at new users. showing how to prepare your models for printing. this video shows how to check and repair a model and how to hollow and add supports and vent holes. it shows the photon slicer software and meshmixer and 3d builder all the software is free. hope this helps new users.

翻譯年糕

討論主題

發文排行榜

回文排行榜

熱門關鍵字