Anycubic Photon Printer Owners 造訪社團

原文網址 Susan Sioux Mercer
2019-01-25 08:29:41

I just woke up, and apparently about 13 hours into a 14 hour print, I ran out of resin. I am hoping I can just print the missing end and fuse the 2 bits together. It is supposed to be a gift for my daughter. Salvageable?

翻譯年糕

Tori Beckett
2019-01-25 08:37:50

Gon Garcia
2019-01-25 08:41:08

Susan Sioux Mercer
2019-01-25 08:42:29

André Nettermann
2019-01-25 08:58:04

Gon Garcia
2019-01-25 09:07:23

André Nettermann
2019-01-25 09:11:48

Susan Sioux Mercer
2019-01-25 09:47:56

Susan Sioux Mercer
2019-01-25 09:48:34

Daniel Ignacio Perez
2019-01-25 10:05:59

Susan Sioux Mercer
2019-01-25 10:27:51

Achraf Jomaa
2019-01-25 11:14:52

Mirko Crispoldi
2019-01-25 16:21:54

Darryl Strong
2019-01-25 20:07:45

Mirko Crispoldi
2019-01-25 20:17:43

El Ner Endem
2019-01-26 00:19:52

Susan Sioux Mercer
2019-01-26 17:59:54

原文網址 Michael Muir
2019-01-25 07:27:20

Okay I give, I have to consult the hive mind on this one. I’ve had my photon for a few weeks and have got some good prints off it but I have a small reoccurring problem, my FEP seems to get just a layer or two of a small section of my prints every time I run the printer. Area that gets this is completely random. I’ve been through three FEP films and each time the same thing happens. The layer is too thin to actually get off of the FEP, I’ve tried everything from soaking isopropyl in it to gently scraping at it with a palette knife. It’s happened with the green included with the printer and with the maroon and black AC resins. I’ve also ran the exposure test on all of the resins and I’m fairly confident I have the exposures set right otherwise I’d assume my issue is under exposure. After my third FEP replacement I decided to ignore it and it backfired, the FEP tore on my last print right on the spot of one of these “layers” and leaked resin onto the screen. Anyone had issues like this or have any advice as to what this is? Setting for the print that caused the rip:0.025mm, 14s, 95s in the black AC resin

翻譯年糕

Michael Muir
2019-01-25 07:30:59

Ken Pooley
2019-01-25 07:54:54

Richard Shapiro
2019-01-25 08:05:13

Terry Reed
2019-01-25 08:52:34

Ken Pooley
2019-01-25 10:32:27

Ken Pooley
2019-01-25 10:35:04

Ken Pooley
2019-01-25 10:40:19

Sen Kun
2019-01-25 16:35:14

Sen Kun
2019-01-25 16:40:54

Michael Muir
2019-01-25 20:15:29

Michael Muir
2019-01-25 20:48:09

Sen Kun
2019-01-25 21:58:21

Michael Muir
2019-01-25 23:15:34

Philippe Maegerman
2019-01-26 02:24:12

Philippe Maegerman
2019-01-26 02:25:10

Michael Muir
2019-01-26 02:27:07

Ken Lim
2019-01-26 09:17:24

Ken Pooley
2019-01-26 11:24:32

原文網址 Marcin ER
2019-01-25 07:02:05

Hi there I have to sell my Anycubic. Maybe someone from here would have been interested. Got it from 14th December, Warranty still on, plus uv lamp, 1l clear anycubic resin, 100ml green, 500 ml ipa alcohol, grey primer, original packaging and all safety gear and tools. 6 prints done. Mainly miniatures. I live in the UK, 350pounds for all.

翻譯年糕

Xavier Cebeira
2019-01-25 07:08:53

Marcin ER
2019-01-25 07:13:42

Micah Vestal
2019-01-25 12:55:55

Marcin ER
2019-01-26 05:03:11

Xavier Cebeira
2019-01-26 05:15:09

Marcin ER
2019-01-26 05:15:57

Marcin ER
2019-01-26 05:17:21

原文網址 Kurt Ploenges
2019-01-25 06:26:22

Hey all, thanks for the add. Love my photon, but get a lot of prints kind of snapping at the supports. The base will print, but the first few layers of support won't take properly and the rest of the print just ends up at the bottom of the vat. Would love to know what I'm doing wrong if any of the experts would care to chime in. =) please and thank you.

翻譯年糕

Derek Reihe
2019-01-25 06:27:29

Mark Wardle
2019-01-25 06:30:18

Richard Shapiro
2019-01-25 06:38:26

原文網址 Rob A Wax
2019-01-25 05:56:53

Ok, so idiot move today. I got a hole in my FEp so I had to change it. So I did, no big deal. I also switched from green to grey resin. First 3 prints fail to stick to the platform. I tighten the FEP, I re level the build plate. Guess what I forgot to do...... Thats right, forgot to change the settings in the slicer for the different resin. DUH!!!!

翻譯年糕

Mark Wardle
2019-01-25 06:26:39

原文網址 Robert Silvers
2019-01-25 05:56:28