Anycubic Photon Printer Owners 造訪社團

原文網址 Phil Davidson
2019-01-19 09:02:43

I'm working on how I can take better pictures, these aren't too great but hopefully good enough to make my point

These are about 30mm high, printed 1 after the other with monocure rapid black at 9s exposures. Printed standing up with heavy supports

I did a quick clean using a resinaway bath then 3 minutes in a Sonic bath again with resinaway then cured under a uv lamp

I didn't take care removing supports, and the sword on 1 got broken.

So can is the difference between the 2 prints obvious? I'm old with poor eyesight and can't tell which was printed at 50u and which at 100u

The paper shared a few days on this ago on this group showed 2 models side by side both at 100u , an fmd print and a sla print , and the difference was remarkable. It got my attention and I decided to test

Print time was dramatically reduced

Next I'll do one of my large giant models (Duncan shadow) to compare
And I'll try to figure out how to take better pictures of black objects

More to follow

翻譯年糕

Mark Wardle
2019-01-19 10:27:28

Mark Wardle
2019-01-19 10:28:48

Miguel Montes Graña
2019-01-19 22:19:28

原文網址 Robert Silvers
2019-01-19 08:42:08

This stuff is insanely strong.

翻譯年糕

John Boyington
2019-01-19 08:45:35

Robert Silvers
2019-01-19 08:50:46

Mikko T. Pyykönen
2019-01-19 09:05:53

Robert Silvers
2019-01-19 09:10:30

Jeremy Lauzon
2019-01-19 09:40:23

Rick Gonzales
2019-01-19 10:09:05

Robert Silvers
2019-01-19 10:12:03

Jason Nech
2019-01-19 10:23:27

Robert Silvers
2019-01-19 10:29:50

Jason Nech
2019-01-19 12:01:01

Robert Silvers
2019-01-19 12:59:16

Jason Nech
2019-01-19 13:08:16

John Good
2019-01-19 13:24:10

Robert Silvers
2019-01-19 13:25:19

Adam Brockmeier
2019-01-19 13:26:00

John Good
2019-01-19 13:26:09

Adam Brockmeier
2019-01-19 13:26:51

Jason Nech
2019-01-19 13:38:08

Robert Silvers
2019-01-19 13:39:08

Robert Silvers
2019-01-19 13:39:27

Robert Silvers
2019-01-19 13:41:26

Robert Silvers
2019-01-19 13:42:46

Jason Nech
2019-01-19 13:43:15

Robert Silvers
2019-01-19 13:43:57

J Pow
2019-01-19 14:09:21

Mariano Loisi
2019-01-19 14:38:35

Johan Bengtzohn
2019-01-19 18:38:42

Jörg Schötz
2019-01-19 19:29:34

Fahrid van Uitert
2019-01-19 19:30:36

Pete Kratsch
2019-01-19 20:02:39

Josh Crosier
2019-01-19 21:53:00

Ben Johnston
2019-01-19 22:15:46

Derek Reihe
2019-01-19 23:06:10

Brian Verkaart
2019-01-20 02:16:18

Jos Mulder
2019-01-20 06:04:20

Robert Silvers
2019-01-20 06:06:47

Jos Mulder
2019-01-20 06:11:59

Bob Leschyna
2019-01-20 10:06:03

原文網址 Garret Bertrand
2019-01-19 07:48:36

No there’s no reason for Batman to leave drink stains on the coffee table!

翻譯年糕

Richard Russell
2019-01-19 07:50:43

Garret Bertrand
2019-01-19 07:51:17

Chris Yarrow
2019-01-19 07:54:26

Garret Bertrand
2019-01-19 08:45:47

Katherine Dewey
2019-01-19 09:11:44

Chris Yarrow
2019-01-19 15:49:38

Dexter WG
2019-01-19 16:35:06

Dennis Batol
2019-01-19 23:46:01

Garret Bertrand
2019-01-20 09:41:13

原文網址 Per Bekker-Madsen
2019-01-19 07:23:21

Hi guys, need some advice. Is it possible to get at smooth surface on the button of the peace. I you the standard settings but gets a very wobbly surface. I use Auto settings.

翻譯年糕

Danny Lloyd
2019-01-19 08:21:03

Per Bekker-Madsen
2019-01-19 15:21:04

原文網址 Chris Yarrow
2019-01-19 06:21:31

Evening all,

I'm just playing about with the slicer and I have a couple of questions about two unrelated .stl files that i'm looking into printing.

1) .stl file 1 is has two components in fixed position. If I could separate them I think they'd both fit nicely on the print plate, however when I rotate or move them they move as a pair. Is it possible to separate them into two .stl objects so they can be added individually?

2) Object 2 is made up of about 30 individual .stl files. Only one of those components is too large despite rotation etc. Is it possible to edit that particular file and chop it into smaller parts, for want of a better term? I'd rather not reduce the scale of the model at this stage.

3) Object 2 again. Some of the parts are so small that I'm wondering if I can stack them in the slicer vertically so they would print on top of each other with supports in between. Now I imagine if this happens it increases the risk of failure. So with that in mind. Is it better to cram as much as possible into the slicer or is it better to print only a few at a time and to not stack them?

They're probably basic questions but I'm trying to play catch up and I have a lot to learn.

Thanks in advance for the help.

翻譯年糕

Josh Reashore
2019-01-19 06:35:35

Chris Yarrow
2019-01-19 06:43:07

Josh Reashore
2019-01-19 06:43:55

Chris Yarrow
2019-01-19 06:44:46

Susan Sioux Mercer
2019-01-19 10:14:57

Chris Yarrow
2019-01-19 15:48:35

Susan Sioux Mercer
2019-01-19 16:22:13

Chris Yarrow
2019-01-19 16:27:28

Susan Sioux Mercer
2019-01-19 16:30:02

Chris Yarrow
2019-01-19 16:33:24

原文網址 Mitchell Smith
2019-01-19 06:08:20

These waves are where the support attaches to the model. Can I adjust exposure time to make this look better or just add more supports?

翻譯年糕

原文網址 Manmeet Singh Buttar
2019-01-19 05:55:26

Printed at 50 micron
Cast in silver
Weighs 11.3g
EasyCast HD Violet

翻譯年糕

Snorri Grissomson
2019-01-19 05:59:48

Manmeet Singh Buttar
2019-01-19 06:00:50

Robert Maefs
2019-01-19 06:07:04

Kyle Bachman
2019-01-19 07:22:35

Rob A Wax
2019-01-19 07:39:39

Rob A Wax
2019-01-19 07:41:20

Rob A Wax
2019-01-19 07:42:37

Manmeet Singh Buttar
2019-01-19 07:54:46

Rob A Wax
2019-01-19 08:15:33

Manmeet Singh Buttar
2019-01-19 08:52:58

Kane Wills
2019-01-19 11:03:23

Kane Wills
2019-01-19 11:04:32

Kane Wills
2019-01-19 11:04:42

Kane Wills
2019-01-19 11:06:18

Tej Joshi
2019-01-19 16:29:44

Kane Wills
2019-01-19 16:39:03

Tej Joshi
2019-01-19 16:42:29

Kane Wills
2019-01-19 16:43:41

Manmeet Singh Buttar
2019-01-26 02:50:01

Manmeet Singh Buttar
2019-01-26 02:50:41

Manmeet Singh Buttar
2019-01-26 02:52:06

Bryan Hartmann
2019-01-26 03:05:12

Kane Wills
2019-01-26 08:36:35

Kane Wills
2019-01-26 08:40:31

Tomasz Dębicki
2019-07-15 19:35:16

Manmeet Singh Buttar
2019-07-15 22:31:14

原文網址 Jason Saiter
2019-01-19 05:43:00

Hello all and thanks for the add. I am pretty new and just wanted to ask the members to check the supports on this WW2 radar dish model I am trying to make. I have several different attempts posted in the photos

翻譯年糕