Anycubic Photon Printer Owners 造訪社團

原文網址 Michael Goldberg
2019-01-06 07:56:53

Need some advice. Trying to print this huge piece. Tried it earlier but it failed before the supports could even be printed. I was using 50% heavy support density shown below. I'm now thinking about using 75% density with .8 or 1.0mm top diameter and 1.2mm lower and bottom diameter. I can't put a raft in because it's outside the build volume and I fear it still wouldn't print. This orientation and oriented the opposite way, vertically down, are the only orientations I can print in. The part is just too large to print any other way. Any suggestions?

Also, yes, I've considered printing it in 2 smaller parts but I'd then I might lose some detail and the top surface has be completely smooth (joint-wise speaking). Printing in two would result in a ragged joint. I've printed a different part in 2 sections and that was the result. Also resulted in a wavy surface on 2 sides, much moreso on the bottom surface close to the build plate.

翻譯年糕

John Boyington
2019-01-06 08:21:54

Evangelos Agas
2019-01-06 10:07:01

Michael Goldberg
2019-01-06 10:07:15

Michael Goldberg
2019-01-06 10:08:04

John Boyington
2019-01-06 10:26:05

原文網址 Shawn William Spencer
2019-01-06 07:46:57

So if I wanted to design a miniature to 3d print. What programs would I need to learn So if I wanted to design a miniature to 3d print. What programs would I need to learn 翻譯年糕

Chad Elstad
2019-01-06 08:27:08

Shawn William Spencer
2019-01-06 08:28:13

Tony Boutwell
2019-01-06 08:54:47

James Heneghan
2019-01-06 09:20:00

Robert Silvers
2019-01-06 09:22:59

Velvet Mark
2019-01-06 10:56:11

Jeff Timothy
2019-01-06 11:13:32

Michael Fairall
2019-01-06 13:09:54

Scott Fairburn
2019-01-06 15:39:16

Dominic Goff
2019-01-06 21:10:12

Sean Pollman
2019-01-06 23:32:32

Russ Charles
2019-01-07 05:22:30

Francesco Antonio Pizzo
2019-01-07 05:38:38

Russ Charles
2019-01-07 05:52:33

Shawn William Spencer
2019-01-07 09:31:11

Scott Fairburn
2019-01-07 14:43:08

Marco Zannini
2019-01-07 17:27:12

Joel Ligeiro
2019-01-07 21:23:50

原文網址 Nick Williams
2019-01-06 07:38:42

Guys, girls, how do I delete this thin ass layer?

翻譯年糕

Stefan Giudici
2019-01-06 07:41:56

Wesley Dowell
2019-01-06 07:46:42

Vinicius Silva
2019-01-06 07:48:45

原文網址 Tony Boutwell
2019-01-06 07:08:17

For ChiTuBox V1.2.0 - In the PRINT dialogue Is Bottom Light-off Delay the same as Light-off Delay? I didn't see that variable in our docs-google file. Setting it up to print my first sculpture using the anycubic green at .02 layer height.

翻譯年糕

Sean Poeschl
2019-01-06 07:21:45

Tony Boutwell
2019-01-06 07:44:58

原文網址 Sean Poeschl
2019-01-06 07:03:48

Thinking about finally venturing away from Anycubic Green to an opaque resin. I mostly print miniatures at 6mm-8mm scale, or 28mm scale. Anecdote seems to show that Monocure Rapid Grey or Gunmetal Grey would be the preferred resin, but I'm open to suggestions.

Also, I'm curious about the differences between opaque and translucent resins in terms of final product. My gut feeling would tell me that an opaque resin would have better detail on the build plate end, since translucent resins would let additional light seep through the model itself, curing those plate layers more over time, but I could also be a total idiot for thinking that.

翻譯年糕

Sara Sisco
2019-01-06 07:23:29

Richard Shapiro
2019-01-06 23:23:22

原文網址 Corey Hallgren
2019-01-06 06:51:07

Question for the group....

My photon is on its way to me, but I'm concerned about fumes.

Is there any reason not to cut a hole in the case of the printer and attach a small fan and ductwork to create negative pressure inside the printer and extract fumes out he duct? I'm thinking a 60mm or 80mm computer fan.

I'd like to be able to use it in the living room. I have a nice work desk set up with my fdm printer on it and space for the photon too

翻譯年糕

Carla Birch
2019-01-06 06:57:33

Mike Bauers
2019-01-06 07:02:20

Rose Stumpwater
2019-01-06 07:45:11

Carla Birch
2019-01-06 07:50:10

Carla Birch
2019-01-06 07:50:54

Corey Hallgren
2019-01-06 07:53:22

原文網址 Mark Sauce
2019-01-06 06:36:41

my fep sheet has a small wrinkle in it from a part failing and sticking to it last night, i just finished a 10 hour print and the parts look perfect, but should i change out the fep sheet now or is it good to go for now?

翻譯年糕

Richard Shapiro
2019-01-06 06:51:09

Mark Sauce
2019-01-06 06:57:55

原文網址 Robert Small
2019-01-06 06:34:39

Okay I can actually see this one from here.
It's funny this was one of the first things I tried to 3D print two years ago when I bought my Anet 6.
I've printed it maybe 20 times and I have been able to get really good prints at 0.2 tip but I can see the resin printer is the way to go even so by the time it's done it will be filament print ready to a resin redy also because I know not everyone will buy a resin printer.
And it makes sense to make a print for the resin printer as well as for the filament printer.

翻譯年糕

原文網址 Tony Boutwell
2019-01-06 06:30:12

About to give this dragon a go... unless you see anything weird that I missed in the supports. :) Now I just need to pull the resin numbers for anycubic green.