Anycubic Photon Printer Owners 造訪社團

原文網址 Mark W
2019-01-03 11:11:27

They're so pretty! ? ?

翻譯年糕

David Fikrle
2019-01-03 17:08:53

David Fikrle
2019-01-03 17:08:55

Federico Rafanelli
2019-01-03 17:17:02

Paul Woodroffe
2019-01-03 17:59:57

原文網址 Rafael Anthony Acevedo
2019-01-03 10:48:43

Hey all - trying out Chitubox 1.2 for the first time. First impressions are it is SOOOOOO much easier to use than Anycubic Photon Slicer. Love how it puts supports. That said, do I need to change any of the settings - other than exposure time, bottom layers/time, and resolution? I have never seen settings for the bottom light PMW, Light PMW, bottom lift distance, lifting distance, lift speed and retract speed. Should I leave those all at default values?

翻譯年糕

Rafael Anthony Acevedo
2019-01-03 10:56:40

原文網址 Jonathan Raymond
2019-01-03 10:46:27

This looks a bit like one of the problems I've seen in the known issues guide, the "LCD screen flickering during print or corrupted and shifted layers or artefacts" posts have some somewhat similar prints

That said, this has only happened once, and only affected one half of the print bed this was on (we've also had some problems with prints not adhering to that side of the plate? Maybe related?), the other half of the print bed had some stuff on that was not affected at all

Anyway, is this something to worry about? I notice people are suggesting this is caused by loose wiring/dodgy soldering? If that's the case it seems like it might be better to do something about this sooner rather than later

Thanks for any attention :)

翻譯年糕

Jonathan Raymond
2019-01-03 11:11:30

Sen Kun
2019-01-03 19:16:00

Sen Kun
2019-01-03 19:21:17

Jonathan Raymond
2019-01-03 22:02:39

Jonathan Raymond
2019-01-03 22:03:33

Jonathan Raymond
2019-01-04 06:46:17

Jonathan Raymond
2019-01-04 06:50:12

Jonathan Raymond
2019-01-04 06:51:04

Sen Kun
2019-01-04 14:53:35

Vinicius Silva
2019-01-04 18:57:42

Vinicius Silva
2019-01-04 19:01:11

Jonathan Raymond
2019-01-05 11:54:20

原文網址 Alisson Gois
2019-01-03 09:48:29

DISASTER HAPPENED. Please, help.

In my first printing the USB was showing the file on the screen of the printer. So I did what Anycubic YouTube channel tells: open the back door and verify if the male USB conector was loose, and it was. So I plugged it back but it is not tight enough in my opinion. But at least the printer showed my file and I hit print.

After one hour I decided to pause to check if tere was enough resin, I noticed that the preview LCD was not showing the image (a dog) it was showing half noise. This was the result:
And the resin in the vault is cured and I can't remove even with IPA.

What's the problem? What do I do? Please help. ? ? ?

翻譯年糕

Robert Maefs
2019-01-03 09:55:30

James Cachia-Garrett
2019-01-03 10:11:17

Manuel Galán
2019-01-03 13:19:12

Sen Kun
2019-01-03 15:29:19

Alisson Gois
2019-01-04 08:23:20

Sen Kun
2019-01-04 15:03:11

Sen Kun
2019-01-04 15:04:13

Alisson Gois
2019-01-05 01:10:26

原文網址 Dylan Trinh
2019-01-03 09:30:04

Details are amazing.

翻譯年糕

Kelvin Pang
2019-01-03 10:45:30

Duncan Nodarse
2019-01-03 12:35:04

Arthur Ng
2019-01-03 12:43:27

Thiérry Fortunér
2019-01-03 13:12:18

Sen Kun
2019-01-03 20:33:08

Michael Zinski
2019-01-03 20:47:35

Michael Zinski
2019-01-03 20:48:01

Danny Lloyd
2019-01-04 04:56:23

Dylan Trinh
2019-01-04 05:09:03

原文網址 Patrick Nixon
2019-01-03 09:22:24

It's been a while since I've done anything with my photon. I think I need to go back to the beginning. Is there a good guide that I should follow? Which program for supports and slicing?

Thanks!

翻譯年糕

Jean-François Meloche
2019-01-03 09:23:49

Sen Kun
2019-01-03 20:29:10

原文網址 Mitchell Smith
2019-01-03 09:11:25

Stoked....getting my anycubic photon here in about 3 hrs-ish

翻譯年糕

Mitchell Smith
2019-01-03 11:31:39

原文網址 Robert Silvers
2019-01-03 08:52:09

Modeled a nut and bolt.

翻譯年糕

James Hastings
2019-01-03 09:51:07

Robert Silvers
2019-01-03 10:32:26

James Hastings
2019-01-03 12:32:01

Gerhard Wilkens
2019-01-03 14:44:28

Robert Silvers
2019-01-03 14:50:00

Gerhard Wilkens
2019-01-03 14:56:17

Mustafa Sengor
2019-01-03 22:25:46

Mustafa Sengor
2019-01-03 22:27:23

Gazsó Péter
2019-01-04 00:50:12

Robert Silvers
2019-01-04 02:17:51

Thomas Plum
2019-01-04 02:32:17

John Boyington
2019-01-04 03:26:22

Trea Cotton
2019-01-04 07:10:50

Robert Silvers
2019-01-04 07:33:34

Vinicius Silva
2019-01-04 07:46:11

Trea Cotton
2019-01-04 08:36:54

原文網址 Nikola Petrov
2019-01-03 08:25:26

Allright, heres a million dollar idea:
What if someone make uv resin that its changing collor according of exposure time, and than "locking" at that particular color, once "activated"? We could literally have full color sla printers, all we need to do is to set exposure time on certain parts by using software that can set every layer pixels exposure separately. Not sure if i explained this well now...

翻譯年糕

Miha Presker
2019-01-03 08:28:08