Anycubic Photon Printer Owners 造訪社團

Dingo

Check the connection first, but it may be time to replace the screen entirely.

Same as above. I had this issue and photon sent me a new screen since mine was only a month old when this happened

Yamamoto Tifa Thank you, and dont you know how much is guarantee given. I mean is it still possible to replace it for free. I bought it last summer

Good luck! Contact either Photon directly or the person or company that you bought it through. I bought mine through Amazon and they helped me connect with photon. I meant it was a little difficult to reach out to them myself because there is a languag e barrier. The emails were all in English but I'm not sure if all of my intent made it through because some of their responses were off topic or seem to ignore something I already said. Eventually I was able to get a free screen from them

Jim Nelson Thank you, and dont you know how much is guarantee given. I mean is it still possible to replace it for free. I bought it last summer

Abror Orifkhonov I just checked and the screen is warrantied for 3 months. It's considered a consumable, because they do wear out over time.

Mine does that from time to time. Usually I turn mine on without the usb plugged in. Test the screen then plug the USB in and continues to work fine - I'm guessing mine is going to need a replacement soon too though. That trick likely won't work for too much longer

Dial down the exposure

Try 10 sec, experiment with lower if it ain't perfect

Sandro Pateishvili would 9 sec be too much of a jump from 12?

Yea I'll give that a go cheers

I generally go down in 0.5 seconds when trying to balance quality vs the whole think dropping off from supports not printing effectively. You could test print this head a few times over as safe test as wont take too long

Brent Mayhew download the Ameralabs test print and print at different exposures to gain an insight into best settings

Whoaaa....that’s way overexposed and ya probably got nowhere near the detail you should...8s is awesome for .04 layers....you’re doing .02(which really isn’t helping but that’s another story)

looks awesome but 12 seconds sounds like you're over exposing it. Off the top of my head i'd say somewhere between 4 - 6 should be about right but i don't have a whole lot of experience with anycubic grey.

My friend you can get way better detail. I use 4 seconds for .02 with opaque grey.

Try a different file. If not try a different slicer

Maybe a corrupt file I always check slice layer by layer...

Reformat your USB

Stuart Finesilver i did that also

David Cornell i will try. Thanks

Did u have models hanging off the build plate somewhere in the slicer? I got this when I had a duplicate sitting out of sight in the background off the build plate

Also, does the print time seem unreasonably longer than normal?

Casey Frank no, all was clear and only inserted one piece to print. Was a print of 12 hours. The sliced model looked good, i checked the layers

Casey Frank well i noticed a different between the time that chitubox gave (9+ hours), and the Photon S itself (12+ hours)

Can the current firmware support chitubox?

Can u recall this problem start to happen after u started doing something different? Like did it start right after u got new usb?

Casey Frank no, 26% of the print time. And why i realy dont know. I have printed last days different items and did have that problem a few times. The sliced model i checked.

Jurjen de Quelerij so u have dif usb, have u used dif slicer?

Casey Frank no all the same slicer amd the same usb

And I see u mentioned u check every layer, it may really just be a firmware problem

Oh

Try dif usb

It is the latest firmware version

Casey Frank yes i will

Does ur usb have connection issues?

Casey Frank no not that i know of

The white usb can with my photon s started having connection issues

I think cheapest solution first, try dif slicer and if it still shows, try reformat usb or buying new one

Casey Frank i know that the white one is bad so i bought a new one.

I will reformat it first. What is a good other slicer?

Keep us updated if it still shows

Jurjen de Quelerij I really like photon workshop that comes with it

Casey Frank i will do so and i will also try it with Workshop.

Awesome, I have some green and was thinking about printing a slimer

Hollowed it out but you can still see some got stuck, happy though, looks better than in the pics!

Lee Rogers I use a little hand drill when I do that :)

dat butt tho

Ryan Pennington first print I used some infill...however it got stuck in various chambers I hadn't put a hole ? zero infill this time, but a drill is a good idea ?

Lee Rogers I bought one of these cheap sets from Amazon

Ryan Pennington ideal, looking now ?

Ghost Cheeks!

That ghost cheeks clap tho

that ass lol

I have used it on really thin foam before that would move and bend. The rub and buff didn't crack or anything but I also had the smallest amount on them as well.

my normal stockist is 5 pounds a litre you can now only buy at 25 pounds. tbh i just stopped printing the health service needs it more then me.

I bought this off eBay, £10 for 5 litres. The day after I bought it the bad feedback started showing up. Needless to say it didn’t arrive so Ebay was informed. Item was removed from Ebay, followed not long after by the seller. Got my refund.

Its probably a scam, I brought some a few weeks ago then Ebay sent me a message saying they were removing the item as it was suspicious. Still haven't received it and I'm having to open a case as the user won't respond

Honestly it does make the most sense its a scam, I bought it before making the post lol. I was kinda expecting it but I figured 10 bucks was a small enough gamble to make lol

5 Litres should be closer to $25 on a normal day. Total scam. I bet if you check the item location it is USA: USA.

I really should have checked here before buying it... lol oh well. Biggest reason I went to try it was the person had a 100% rating on ebay

I was buying 99 IPA locally at around that price before corona hit.

Tried to buy ipa from eBay last week. , £11for 5 litres.
Didn’t arrive and I got a refund.

I just looked at some of those listings: the sellers have either were low feedback numbers, meaning they haven’t been selling many items, or they have no recent feedback so the probably are using old accounts to scam people. I always encourage people to report those items to eBay so they can investigate, but unfortunately they pop up as fast as eBay takes them down

‎Carmy Paglionico‎ : You link to a commercial website without terms and conditions and imprint. Don't be surprised if you get a warning.

Following

Use the resin exposure test and get the proper setting for your printer ?

3rd attempt, redid file each time

how's the lcd look when testing

I took the vat out and it looked like it was working properly, ran the file without the vat

Jason James Grubb could it be a bad thumb drive maybe, I was getting layers on my prints, like a film across the entire print

Jason James Grubb the rest are in the vat

are you using the original usb? if so its that.

Nathan Kopp I changed that out long ago

What is the deal w the original usb? I haven't had an issue with it. I tried to upgrade based on this group but I got one that was too big for FAT32 apparently. Said piss on it, been rocking the cheap og one ever since

ya i rocked it for a while until it failed at random times during the print