Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Wes Shawshank Crain
2020-03-23 06:02:57

I changed screens and now I have to double my print times. Any ideas? I changed screens and now I have to double my print times. Any ideas? 翻譯年糕

Dave Smith
2020-03-23 06:07:35

Forget to take off the plastic?

Sean Croteau
2020-03-23 06:12:06

Or spacing may be off if you have a glass protector on the screen.

Wes Shawshank Crain
2020-03-23 06:31:37

I dont have a screen protector on and i for sure took the plastic off

Michael Paulick
2020-03-23 07:55:18

Following, because, same here. No protective sheet. Print time went from 7.5 seconds to 13. Same everything except FEP

Gregory Thompson
2020-03-23 08:54:21

Which screen did you buy to replace your old one?

Wes Shawshank Crain
2020-03-23 08:57:04

https://www.ebay.com/....../2560x1440-LCD....../184099653038

Wes Shawshank Crain
2020-03-23 08:57:58

Gregory Thompson that one

Wes Shawshank Crain
2020-03-23 08:58:28

Michael Paulick i changed my fep just to see if it fixed it and nothing I feel your pain

Gregory Thompson
2020-03-23 09:02:37

Wes Shawshank Crain it claims to be an Anycubic brand in the description. I was thinking if it was non-brand that it could possibly be filtering too much light. Hope you get it worked out

原文網址 Wes Shawshank Crain
2020-03-22 01:46:54

Does resin go bad... And if it does is one of the symptoms much longer than normal exposures

翻譯年糕

Gabe Snooks
2020-03-22 10:09:22

Yes and yes

原文網址 Wes Shawshank Crain
2020-03-17 23:48:26

I recently changed my screen it was constantly failing as an experiment I increased regular exposure time and it helped a bit so I basically doubled it and now it works. My question is could I somehow have gotten an under powered screen

翻譯年糕

Shig Bergin
2020-03-17 23:55:53

It would be the light, not the screen

Wes Shawshank Crain
2020-03-17 23:56:31

Would that have gone out at the same time as the screen and if so how hard is that to replace

原文網址 Wes Shawshank Crain
2020-02-24 09:31:09

So I have a strange issue in printing miniatures. When I put more than one on the build plate I get the strangest failures the bottom will print then some supports. Then the legs on some of the terminators will not print from the foot to the knee or hip then the print will print fine after. All of these models are clones of each other. The following troubleshooting has occurred. 1. Re-level bed, 2. Update firmware, 3. Stop using chitubox switched to prusaslicer exporting to photon workshop, 4 changed exposure times, 5. Changed resins. 6. Have tried 2 separate new usb drives one type 2 one type 3. The type 2 would let me select prints and lower the vat acting like it was printing but freeze at 0% on multiple files. The type 3 once plugged in would freeze my photon and the screen would be unusable. If started with the type 3 in the photon wouldnt load past the initial picture saying photon while booting... Please help idk what else i can do

翻譯年糕

Brian JH
2020-02-24 09:42:36

Wes Shawshank Crain
2020-02-24 09:45:07

原文網址 Wes Shawshank Crain
2020-02-23 07:02:20

I have a strange issue I formated a SanDisk jump drive as ive been told a lot of my failures look due to the juno drive. I formated it and loaded it up. I can see the print and select it and start the print but all it does is lower the plate into the vat and stay at 0% and doesnt try to print... Any tips would be appreciated

翻譯年糕

Per Bekker-Madsen
2020-02-23 07:05:50

Ken Cunningham
2020-02-23 07:07:33

Wes Shawshank Crain
2020-02-23 07:10:01

Alexander Bayerdorffer
2020-02-23 08:58:11

Wes Shawshank Crain
2020-02-23 21:59:36

Wes Shawshank Crain
2020-02-24 01:21:12

Ken Cunningham
2020-02-24 01:25:09

Wes Shawshank Crain
2020-02-24 01:56:33

Ken Cunningham
2020-02-24 01:57:47

原文網址 Wes Shawshank Crain
2020-02-16 12:35:18

So I may be an idiot but I cant get prusa slicer to set up. When i downloaded it. It opened straight to a build plate for a photon s but it doesnt read it as resin so it has a bunch of settings and no one for orient or support which is what I wanted for it

翻譯年糕

Paul West
2020-02-16 13:05:58