Anycubic Photon Printer Owners 造訪社團

原文網址 William Babington
2018-11-25 07:11:29

Well, not sure what's going on, but i Can't seem to get power to the printer, green indicating light on power module isn't lit, so thought it might be the power cord, tried another cord but no luck...something else I should look at???

翻譯年糕

Chris Meijer
2018-11-25 07:14:13

William Babington
2018-11-25 08:45:03

Sen Kun
2018-11-25 12:58:12

William Babington
2018-11-26 07:59:27

Sen Kun
2018-11-26 16:06:01

原文網址 Chris Carter
2018-11-25 06:36:59

I wonder if I could borrow the collective intelligence of the group.

I am getting some extra lines at various levels on my prints. These 2 planters were printed at the same time and they both have additional lines not present on the file. The 2 larger areas appear to be a coarser line at regular intervals that I can't figure out and the smaller patch in the middle is quite messy but only appears on that side, not the other side at the same height.

Any ideas please.

翻譯年糕

原文網址 Nikola Petrov
2018-11-25 06:30:39

Is this fep sheet damaged? It looks like little dent done by nail or who-knows-what. Its bit hard to take pic, but i did my best.

翻譯年糕

Andy Chew
2018-11-25 06:35:15

Greg Miller
2018-11-25 06:45:06

Greg Miller
2018-11-25 06:45:48

Adam Widdowson
2018-11-25 06:52:50

Nikola Petrov
2018-11-25 06:54:32

Mislav Glibota
2018-11-25 07:12:37

Nikola Petrov
2018-11-25 07:13:44

Mislav Glibota
2018-11-25 07:18:56

Adam Widdowson
2018-11-25 07:23:32

Alison Friedlander
2018-11-25 07:36:02

Stefan Giudici
2018-11-25 07:37:29

Bronson Ferri
2018-11-25 10:49:14

Yeun-Ee Chen
2018-11-25 11:25:22

Chad Elstad
2018-11-25 17:46:47

原文網址 Paul Rowden
2018-11-25 05:50:18

Love this printer! This is the second print I have done. Lathe
I drew this up in 3D cad ( just learned that) for my n gauge railway layout, first time using Chitubox for supports
Love it! 10 mm length.

翻譯年糕

Flint Read
2018-11-25 17:24:31

Paul Rowden
2018-11-25 18:00:34

Flint Read
2018-11-25 21:03:22

Paul Rowden
2018-11-25 23:56:39

原文網址 Paul Mabbott
2018-11-25 05:13:45

Any advice for best options for putting a carbon filter on the printer? I see there are a few options on Thingiverse for mounts.

翻譯年糕

Rose Stumpwater
2018-11-25 05:38:14

原文網址 Fred Breton
2018-11-25 03:50:28

Next paint job, just need to finish to sand the joints to make them to fit good, and then paint and glue. Done with Monocure Gunmetal at 50um.

翻譯年糕

Luis Alberto Ruiz
2018-11-25 18:40:23

原文網址 Miscel Scorzelli
2018-11-25 02:51:20

evening guys, someone can tell me the settings for the various colors of the resins and the various 0,05-0,03-0,10 micron.oppure a site where to find them, thanks

翻譯年糕

Philippe Maegerman
2018-11-25 03:51:39

Guti Gutmann
2018-11-25 19:24:08

Guti Gutmann
2018-11-25 19:24:56

原文網址 Miscel Scorzelli
2018-11-25 02:36:45

guys good evening, someone can give me the settings or a site where to find them for the various resins of various colors.

翻譯年糕

Richard Shapiro
2018-11-25 08:05:31

Adam Pitzer
2018-11-25 08:44:23

Richard Shapiro
2018-11-25 08:46:55

原文網址 Martin Mjöllnir Umgjer
2018-11-25 02:06:44

My lab (aka. messy storage room) is approaching freezing point. But instead of waiting for stuff to be delivered I looked around at the hardware store and went full NASA on my printer. # SpacePrinter

翻譯年糕