Anycubic Photon Printer Owners 造訪社團

原文網址 Alain Rivard
2018-09-19 04:14:58

hey Guys,,downloaded B9 to make support for my model..but i can't for the life of me figure out how to set a Anycubic profile for it!!!...

翻譯年糕

原文網址 Farryl Bird
2018-09-19 03:59:21

Hi. Iv only just been using anycubic black since Iv had my printer. Iv now just tried my first print with Monocure rapid gunmetal. On my print small fine details seem to just snap of very easily like its soft. Is this how the resin is or I'm perhaps not curing it enough between layers?

翻譯年糕

原文網址 Michael Kingsley
2018-09-19 03:19:07

Partial success!

New Settings : Layer 0.05 | ExpoTime 14s | OT 1s | BotExpo 60s | BotLayers 16
[BotExpo reduced from 90s, BotLayers increased from 10]
Using Monocure 3D Rapid Clear.

I got the model off Shapeways, used PreForm to reference recommended orientation, placed my supports using the Anycubic Software (paying attention to local minima, from now on I will be using FlashPrint for supports). Finally, I put it though the Photon File Validator software to clean up any islands.

Problem : The layers are very visible and the raft is very thin. Could my build plate be set at the wrong height? Or is this timing issue?

The third picture is for reference to the last print I made. It shows similar signs but to a greater degree.

Any advice would be greatly appreciated!

翻譯年糕

Philippe Maegerman
2018-09-19 04:15:12

Francisco José García Morcillo
2018-09-19 04:39:08

Chris Meijer
2018-09-19 05:05:25

Chris Meijer
2018-09-19 05:06:22

Ryan Lawecki
2018-09-19 05:07:38

Michael Kingsley
2018-09-19 05:10:30

Michael Kingsley
2018-09-19 05:11:09

Michael Kingsley
2018-09-19 05:11:29

Chris Meijer
2018-09-19 05:13:41

Michael Kingsley
2018-09-19 05:50:15

Michael Kingsley
2018-09-19 05:51:44

Chris Meijer
2018-09-19 05:54:14

陳彦廷
2018-09-19 06:58:28

Josh Norris
2018-09-19 09:56:27

Michael Kingsley
2018-09-19 10:36:17

Michael Kingsley
2018-09-20 19:07:19

陳彦廷
2018-09-20 19:17:15

陳彦廷
2018-09-20 19:17:35

陳彦廷
2018-09-20 19:17:46

陳彦廷
2018-09-20 19:18:34

陳彦廷
2018-09-20 19:19:30

Michael Kingsley
2018-09-20 19:31:10

Michael Kingsley
2018-09-20 19:35:15

陳彦廷
2018-09-20 19:50:33

陳彦廷
2018-09-20 19:51:56

Vinicius Silva
2018-09-21 03:51:09

Vinicius Silva
2018-09-21 03:55:13

Michael Kingsley
2018-09-21 05:28:30

陳彦廷
2018-09-21 08:32:31

陳彦廷
2018-09-21 08:33:37

Michael Kingsley
2018-09-22 00:12:03

Philippe Maegerman
2018-09-22 01:08:48

Nick Williams
2018-09-22 01:48:57

陳彦廷
2018-09-22 09:09:29

Michael Kingsley
2018-09-22 11:26:02

Michael Kingsley
2018-09-22 11:46:48

原文網址 William Bassett
2018-09-19 03:08:25

Deckard's Blaster
Well it's starting to look like something :)
The dark gray is resin printed parts and the light gray is from my Ender 3. The light gray pieces are too big to fit on the plate and I didn't want to split them and then try to glue them together. Besides, that's why I got the Ender and CR-10s :)

The FDM parts are surprisingly light, almost no weight to them. If I printed everything on the Ender the end prop would feel like holding a plastic squirt gun without any water in it. The resin actually adds a significant amount of weight... and in a good way.

These haven't been cleaned up, just some light sanding here and there but nothing major at this point.

翻譯年糕

原文網址 Demian Marban
2018-09-19 01:13:50

Well, guys, I received my screen replacement after waiting for 2 weeks. I installed it, did my screen test and I'm still having the same splashed screen !!! THIS IS SUPER FRUSTRATING !!! I bought it thru Amazon can they help me out?

翻譯年糕

原文網址 Aaron C Plante
2018-09-19 00:56:58

Finally ran through my first bottle of resin with this awesome printer. Ready to order some more and looking for a variety. Thinking I'll definitely pick up some Monocure Gunmetal and Clear. Also looking for some type of semi-transparent blue. What are some of your favorite resins with this printer and where do you order it?

翻譯年糕

原文網址 Harold Garcia Z
2018-09-19 00:46:29

hello and thank you for accepting my request ...

Someone by chance knows the configuration to print with the resin B9R-4-Yellow ... it's been a long time and I do not have good results ....

I would appreciate any help with the subject ..

翻譯年糕

原文網址 Mike Mellon
2018-09-19 00:24:27

Anyone have settings for anycubic's opaque grey resin, it's all I have left lol

翻譯年糕

原文網址 Ari Isaacs
2018-09-19 00:18:47

Can someone give me there best settings for theses two resins or were to find a chart.thanks

翻譯年糕

Jean-francois Lacassaigne
2018-09-19 00:20:52

Ari Isaacs
2018-09-19 00:26:29

Philippe Maegerman
2018-09-19 00:29:26

Jean-francois Lacassaigne
2018-09-19 00:31:15

Ari Isaacs
2018-09-19 00:33:32

Kevin Lems
2018-09-19 03:20:08

Kevin Lems
2018-09-19 03:20:30

陳彦廷
2018-09-19 11:04:50

Dave Lemsing
2018-09-19 14:14:13

原文網址 Ethan Cline
2018-09-18 23:45:17

I recently purchased some maker juice wax cast resin. My photon was printing perfect before switching resins. Here is their recommended print settings which I’ve followed, however my prints have failed 4/4 times. Usually the failure happens where the support turns into the actual design. Any advice?

翻譯年糕