ATOM 3D Printer Group 造訪社團 » 耗材 模組 副廠零件

Hello everybody,

I would to present to you the different steps of my ATOM 2.5EX printer evolution project:

- Step 1: disassembly of internal electronics + addition of TOP LED rails for lighting (Status => 100% finished)

- Step 2: replacement of the 8-bit motherboard with a 32-bit board (Duet2 Wifi) + addition of Side LED rails for lighting (Status => 100% finished)

- Step 3: development and integration of a 7' paneldue screen on the frame with laser-cutting aluminium parts + folding (Status => 75% finished)

- Step 4: manufacture of a rear plate to integrate the antenna of the Duet2 Wifi board + addition of an inter-switch for the internal lighting of the printer (Status => 75% finished)

- Step 5.1: replacement of the original nozzle with an 24v e-3D v6 standard version + a 24v Dragon Hotend version (Status => in progress 75% finished)

- Step 5.2: developpement and integration of a PCB for rapid disassembly of the print head, it's the same principle as ATOM 2.5 FX (Status => PCB are 100% developped and PCB manufacture is 50% finished)

- Step 5.3: replacement of the 12v power supply with a 24 volt version from Meanwell. (Status => to be mounted)

- Step 5.4: installation of a 24v to 12v converter to keep the original heating bed in 12v. (Status => to be mounted)

- Step 6.0: finishing integration of the 2 DYZE Filament sentinel to be able to stop the print when wire is out.

- Step 7.0 : integration of the ATOM laser module (if possible with the Duet2 Wifi). For this last step, I'm not sure if I can connect and run the laser on the Duet Board. I need to check first...

I will give you news about my project in few days / weeks...

✋

翻譯年糕

ATOM2.5雷雕初測

[已售出]

因為公司政策的關係，想要賣出

ATOM 2.5 ，加雷雕模組，

使用正常

附加一些材料

透明線材一綑，3D列印膠帶，工具，螺絲

機器在新店，無外箱，請自取

售價: 10,000(可議)

(說明書和技術問題請聯絡ATOM官方，他們都會協助)

意者請私!

[售] 因為公司政策的關係，想要賣出。

ATOM 2.5 FX 整機方案，有加雷雕模組，於今年5月多購入，使用上一切正常。

有包裝外箱。

附加一些材料 >

明耀 - 白銀，黑銀，鈦金，炫帝金，邪眼藍(全新)，赤焰紅，皇上黃，明亮橙。

SpiderMaker - 消光鐵灰，消光炭黑

Botfeeder - PETG，夜光料

3M耐熱膠帶

機器在汐止

預計售 60000 (可議)

有興趣請私問喔~

更新～己售出

太多台-年底清空間

售一台 ATOM2.0 有雷射頭 已改光學限位 無熱床

機器運作正常,可當面驗機交機-含使用教學

預售18000元(誠可小議)

機器在台中-限面交

After having heat fluctuation last month and fix the problem by wrapping Kapton tape around the heating plate area & nozzle to keep heat steady and it work.

Now, my new problem is having Max-Temp and printer stopped within 10% of print outs only.
What is going on ?

Any input and suggestion will gladly use.
Thank you in advance!

翻譯年糕

幫麥克風作了收納套件，有 3D 印表機之後這些小東西真的很方便可以自己做

ATOM 3 列印

已售出，謝謝。

[售] ATOM 2.0 + 雷射頭 台中豐原自取 1.2 萬。(防護罩要找一下) 進倉庫前偶爾使用。

不知不覺4年了，歷經熱床升級、2.0升2.5ex、0.2噴頭模組化、雷雕、強化支架，不知被扒了幾層皮，雖然一度有丟資源回收的念頭，但謝謝你4年來讓我成長不少，也認識許多好朋友…

家裡的 ATOM 2.5EX 使用率不高，不知道有沒有人有意願購買？若有意願，請私訊。

機器是 ATOM2 升級到 2.5EX
有熱床、有雷雕模組、限位開關是光學的、還有一些備品可以一併給。

PS: 它運作是正常的。