ATOM 3D Printer Group 造訪社團

原文網址 Genu Wu
2016-02-11 10:24:40

[分享]改良2.0盤面夾具
鎖到有點緊就可，不用再往死裡鎖，拆盤子也只要鬆兩顆鎖絲

Kwok Tony
2016-02-11 10:32:15

圖在哪?

Bise Chen
2016-02-11 10:41:49

我個人的想法，這個其實可以去腳踏車店要內胎，剪幾片來墊底就好了，不用特地再印。

林祐生
2016-02-22 15:20:40

有圖嗎？

原文網址 劉柏葳
2016-02-11 07:32:52

不好意思新手想問個問題
在效正都一直脫桿
是哪個部分有問題嗎？
而且噴頭碰觸到列印平面的聲音超大要調整什麼呢？
微動開關也一直有在調可是還是一直脫桿？

廖新弘
2016-02-11 08:26:40

上蓋拉鬆一點看看

廖新弘
2016-02-11 08:41:11

https://atom3dp.squarespace.com/new-index-chi

李穆
2016-02-11 09:23:46

微動開關螺絲頂太剛好，點兩下上蓋板金疲勞了就彈不回來，螺絲多轉90度進去就會好了

Mark Chen
2016-02-11 18:28:13

螺絲鎖太深?

劉柏葳
2016-02-20 17:11:05

謝謝

原文網址 Uwe Schall
2016-02-11 02:20:26

PLEASE HELP!!
I finished the build of my 3D printer, but JUST ONE motor works. (the X motor) if I connect other motor to X, that one works. no idea how to solve the problem.

翻譯年糕

Birk Binnard
2016-02-11 03:42:37

All the motors are the same. Check each motor connected to the same stepper controller. Does each one work? If yes then your stepper controllers are bad. If no then your motors are bad.

Joschka Friedl
2016-02-11 09:04:57

So - every motor works on The X slot, right?Now then put The Stepper driver from The x slot to The Y slot and test again. Do they work?If yes, all other drivers have a defect (or too less vref? Im not familiar with that topic. You should definitely che ck those!) But if it doesnt work - First test that driver again on X slot - and The others too.If all drivers work on X slot, your Board has a defect!
And if The drivers dont work but The x one works on all other sloty, your drivers have defects.

Uwe Schall
2016-02-11 12:17:49

Thanks for the advice!! I didn´t think of the drivers. Will test that next. one more strange thing: if I let the motors connectd in their correct way, (X in X, Y in Y...) and change THE BLACK stopper cables, same effect!!! just the X-stopper cable lets the motor move. exaple: if I put the X cable on Y position, Y motor moves!! (I mean the double-black cables connected to the end stoppers)

Clarence Lee
2016-02-11 17:39:58

Looks like your endstop problem...
ref this to do the check
https://atom3dp.squarespace.com/power-on-testing....../

原文網址 Shih-Yen Lo
2016-02-11 00:21:36

抱歉由於回文不能po影片所以重發一篇

感謝回覆上篇的各位，我今天照著各位的建議調整了一下，不過仍然沒有改善，我有用手指壓噴頭確認微動開關的作動(機構咯咯聲)、確認列印件沒變形、噴頭前螺絲上的彈簧沒有卡住，並降低速度再測。至於開關的線路問題由於目前手邊沒電表，不過我有在執行auto level 時用手往上壓噴頭，是有反應的，但是只有在固定幾個點，能請大家再幫忙看看嗎？謝謝

李穆
2016-02-11 02:41:50

接上電腦用PronterFace連線後以M119指令查查看你的微動觸發情形

Timy Fat
2016-02-11 02:59:36

我之前也是這樣
試試再擰緊一點？

Joe Abaquin Bing Aquino
2016-02-11 05:56:06

I keep getting the same problem no matter how I adjust.
Sometimes it works, sometimes it touch half of calibration and half is in the air.
There should be other way fixing this.

廖新弘
2016-02-11 08:24:17

M119檢查沒有問題的話，檢查一下上蓋的微動開關的固定螺絲，或者先把料管跟電線獨立分開試試

廖新弘
2016-02-11 08:30:42

還有放鬆一點上蓋後面固定螺絲

吳昌駿
2016-02-11 13:51:39

重新調整螺絲看看，我也有碰過條一條就PASS了

Shih-Yen Lo
2016-02-11 23:46:11

謝謝各位，經過多方嘗試以及三用電表的出動，找到有一個電線焊接處的熱縮管內電線斷裂鬆脫導致接處不良，目前已暫時用鐵絲銜接起來並測試正常，明天再去光華買料來補焊
謝謝各位的幫忙，也提供大家參考

原文網址 Mariel Diaz
2016-02-10 19:38:17

Hello,
I am trying to 3DPrint test specimens, but when I change infill style...the infill pattern of the specimen does not change...does anyone know why this is happening?

翻譯年糕

傅耀儀
2016-02-10 19:55:16

The object is too thin.

Andrew Lee
2016-02-11 03:49:19

These layers are part of the transition from solid skin infill (set by skin thickness) into the sparse infill (set by you)

原文網址 Birk Binnard
2016-02-10 04:40:04

Nice print - almost!

20 hours 33 minutes is certainly better than the Craftware estimate of 2+ days. The first pic shows the finished part - it looks really good on the outside. But pic #2, looking up at the inside from the bottom of the part, shows some bad layers and loops.

Because that badly affects how the light from the LED at the base shows through the sides I am not posting the STL for this design. Instead I am going to change the design a little and make the shoulders of the part less horizontal. That should eliminate the bad loops and result in a nice smooth inside too.

翻譯年糕

Birk Binnard
2016-02-10 07:16:41

Updated version (now printing) will look like this.

Edit: Well, it seems I have some sort of extruder problem (again); after restarting the print 3 times it seems the hotend is extruding only about half as much PLA as it should. So tomorrow I'm going to try the propane torch solution: heat up the nozzle red hot and vaporize any obstruction that might be in there. …… 查看更多

Joschka Friedl
2016-02-10 17:44:02

Good Luck on this one!

Birk Binnard
2016-02-11 03:39:34

Well it looks like that helped. Here are some results from the process:

1. When I disassembled the hotend the PTFE tube stayed in the nozzle. When I pulled it out I noticed a small amount of "black stuff" on the nozzle end of the tube. I scraped thi …… 查看更多

原文網址 Roy Lo
2016-02-10 01:57:41

Cura 切片, 溫度 185 ~ 190 , 五種線材,
頭, 身體, 手臂壁厚 1.2 , 層厚 0.2, 關節太緊, 不易接合
腿部改成壁厚 0.8 , 層厚 0.15, 關節接合容易多了

http://www.thingiverse.com/make:192701

原文網址 Shih-Yen Lo
2016-02-10 00:59:49

Hello 各位，

我來求救，我今天把一代 Atom從公司搬回家裡，結果一道加裝起來就出現影片中的問題。本來他執行 auto level 的時候完全碰不到玻璃板，後來調整了噴頭上校正的微動開關那兩顆螺絲後現在變成這樣，請問有人遇過類似的問題嗎?

謝謝各位

張張家祝
2016-02-10 01:20:12

在auto level的時候把速度放慢到30%應該可以解決，我也碰過所以就把速度放很慢就正常了，試試吧

Timy Fat
2016-02-10 01:24:52

前幾天試過
李大教我 auto level時速度放到最慢，微動開關螺絲比剛碰到再擰緊一些
就好了

Mindaugas Ramaška
2016-02-10 01:33:46

Adjust sensor. It need to click when touch force greater then you have set in the video

Yinka Alade
2016-02-10 04:12:08

Yea, I had this problem yesterday. Resetting the sensor to make sure the screw is close enough to click the switch was the issue.

Genu Wu
2016-02-10 08:19:59

速度太快

James Lin
2016-02-10 09:28:24

明顯只是螺絲沒有先轉好喔，
轉好再做Auto Level吧，
參考說明書一下 ~

James Lin
2016-02-10 09:32:48

微動開關與螺絲的距離

廖新弘
2016-02-10 09:52:37

1.你有確定微動開關在用手指頭壓噴頭實有聲音嗎

廖新弘
2016-02-10 09:53:42

2，噴頭前的螺絲上的彈簧有沒有卡住

廖新弘
2016-02-10 09:54:26

3.你的噴頭列印件有沒有變形了

黃小濤
2016-02-10 13:03:34

螺絲鬆了，或微動開關電線接觸不良

李穆
2016-02-10 13:26:42

拉蓋彈簧沒壓緊，微動螺絲沒頂到位，上蓋樞紐阻力太大，微動沒焊好，都有可能

Antony Hus
2016-02-10 15:51:22

我也是這樣有跟原廠要資料原廠給的資料檔案你參考看看傳檔案給你這裡沒辦法附加檔案要加入好友

Chuck Chen
2016-02-10 16:56:16

我的是二代機，有可能是整線時拉到了，我就有這個狀況，後來直接把線拉到一個位置用膠帶貼好即可

Jacky Tseng
2016-02-10 18:37:33

微動開關有問題, 沒有回彈.

原文網址 Mars Wen
2016-02-10 00:31:51

atom外傳

姊：什麼！我多按一個複製列印鍵！！！

妹：Hi!我來平分你的奶粉了！

原文網址 Birk Binnard
2016-02-09 23:34:13

66% done after 15 1/4 hours

It looks like Craftware's print time estimate is not very accurate. My guess is the total print time will be closer to 20 hours. So far there have been only a few extremely fine strings across the inside - I specified random start points for each layer to avoid any outside seam. The outside surface quality is excellent.

翻譯年糕