ATOM 3D Printer Group 造訪社團

如果大家有印成功，麻煩補個照片讓小弟觀摩一下。 <3

hardware 那頁可以補個bed roughness 0.15搭配你這個layer 0.05
這樣第一層就會是0.2mm不會那麼難印..

噴頭微動開關的觸發行程應盡量調到最小~

在哪裡???

其實這兩個都不需要開 Prime Pillar. 新同學的話還是先試試看層高別那麼極限吧～ 然後可以看看進料機構那邊手臂是否鎖太緊，或進料齒輪是否乾淨。溫度也可以試試看高一點，最近比較冷

列印件冷卻風扇關到0，brim開大到15mm，skin thickness 0.6或0.4

冷卻風扇關到0 是把 FAN/COOL 的三個值都調成0嗎?

cool以外調成0

這個設定不太理想。
Min jump 10
Trigger 15
Prime 5
Suck 5
Wipe 3
Min Layer 0.5
你原本的設法表面會不漂亮，容易卡料，還有小面積的地方會燒壞。

還有要看有沒有改快速接頭回抽

請各位大大指導!

倒著印可能會更好更快

sounds like "E. Distance between end stop and screw".
check this website to fix it,step by step.
if still same,just try to print something and take first layer photo. …… 查看更多

Hey there :)The carriages do the sqme thing on my printer. When they hit the endstops i always worry if it smashes them :D never thought about asking that.About the fans: Did you load the kisslicer settings from the support webpage? It should allow coo ling above 3mm height. It can be changed in kisslicer. If you found and tested it, check the cables in The cable collector. In mine the Z-endstop in The effector got disconnected :DAnd about slicing Software: Try some until you find yours. At The Moment i'm happy with cura, slic3r gives a bit more Options but has more complexity to it.I mostly print with sd because then I can turn my pc off ? Best wishes

hi,new atomer. it's normal,but u can try slow down when it auto-leveling. the first layer will be better.
just take look the photo.
https://www.facebook.com/photo.php?fbid=751011125024969&set=pcb.1639232102981745&type=3&relevant_count=3

thanks a lot, how to slow down when autolevelling ? by adjusting the fr percentage with the knob on the printer?

Yep, that will work. Sounds awkward for the First Moment, sound of The stepper motors i mean. But sadly it wont change much. It will still be going with full Force to hit the endstop. Just with less speed

yep!!! u right.
u need slow down it before it touch first point on plate.
then the sound will be lower and the first layer should be smooth.

mmmm.... maybe u should change the acceleration in the marlin. X,Y,E 9000->500 it should change a lot.

i remember you can change acceleration on LCD.
control > motion > acceleration ?

I was wondering why they put a Firmware up where this is not changed from the beginning? :o

Who knows

https://www.youtube.com/watch?v=H9Al873W3LY

I hoped somebody hear would have known :D

ah...of course u can do that. u just need change all firmware for auto-level. but not so much info for that.
for official version u only have two choice to slow down that. that's all i known.

Why does the printer in this video do multiple taps at each location? My printer does only 1.

Maybe because it's atom 1.0? Was even wonderig because mine starts on C / Z tower, in the back of the printer while this one starts on the A tower, the left one. But this could only be a mounting thing with the Display :)

It's a special branch based on
https://groups.google.com/forum/......
IT's trying to probe the same point till it's repeatable result.

There are also another change to average probe result
"Changed autoprobe behavior to average instead of exact match "
http://www.simplyalt.com/atom/viewthread.php?tid=1001......

Yes, It's the day I finish the assembly of the ATOM1.0
I wired the x,y,z motor in the wrong order. So, it's moving order is reversed between x & y tower
original video is this one
https://www.youtube.com/watch?v=msVoXpr2WII

That's an interesting set of modifications - but an old version from back in 2014. Is there a current version that includes those same mods?

thanks for the answers, i'm trying new settings and making tests.... in fact the printer is ok, but there is a problem when it start printing from the back side (near the Z axis ) : the head keeps scratching a bit the bed no matter what i do with Z offset tweaking, the min Z offset is good when i put a sheet of paper under the head when it's making the process, but i see that when it start printing near the perimeter near Z axis , the head touch the plate... like if the Y arm was too short and the head not exactly horizontal, so it touch the bed.... Any ideas ? i re tight the belts, redone Z offset etc ... nothing change ....