Anycubic Photon Printer Owners 造訪社團 » 用戶發文

From 2D to 3D printed (except the Darth Vader helmet, that was store bought).

翻譯年糕

https://youtu.be/IdikH6ELbXQ

Anycubic support wants me to test the Z motor, but the link to the video they sent shows this error message. Does anybody have a working link to that video? The second link they sent on how to test 13 46 pins of the motor with a multimeter works. I just need the video on how to actually remove the Z motor. Thank you.

翻譯年糕

I attempted to print a file on my photon. 1.5 hours later, the print finished but I noticed the Z motor never moved. Now, I cannot move it with up and down arrows. I powered it on and off. Unplugged and replugged. Did a firmware update and an eeprom reset but none of these worked. Prior to this print, I did an exposure finder test where I had to click on test mode.gcode, but I later clicked on the print mode. to revert back to the peeling action. Any possible solutions or suggestions to fix this issue?

翻譯年糕

Annoying screws keep falling off? Cut a piece of straw and use it as a guide. Frustration free screwing ? .

翻譯年糕

The Printer Blob Chronicles. Now Anycubic Support wants me to measure the voltage of the Main Board. Am I measuring it right? The voltage between the L12 chip and the GND PORT of the U12 chip as seen on my pic is only 0.33, when the normal voltage should be between 5.9-6V. Could this be why my printer is printing blobs?

翻譯年糕

Update: The Blob Chronicle woes culprit was not resin related nor was it caused by defective LCD. It turns out my main board was faulty, giving intermittent output and variable results. Some times good prints but mostly failed prints including the blobs, making it extremely difficult to diagnose the problem and caused a lot of confusion on my part and to the very kind photonsters who were very nice to help me with my problem. I got my main board from Anycubic and although, I haven’t had the time to test it out thoroughly yet, my first 3 prints since the main board replacement have been successful ?? .

The dreaded blob is back (scratching my head) and I don’t know why. I used 50% Monocure Rapid Clear and 50% Monocure Flex100 with the the pictured settings. Used the exact model, resins and settings on the phrozen shuffle and it came out fine. Prior to this I printed a monorook calibration model on photon using 100% Monocure Rapid Clear and that came out alright. Could it be that my Photon doesn’t like resins (Monocure or otherwise) mixed with Flex100? So mind boggling this elusive mystery blob.

翻譯年糕

Update: The Blob Chronicle woes culprit was not resin related nor was it caused by defective LCD. It turns out my main board was faulty, giving intermittent output and variable results. Some times good prints but mostly failed prints including the blobs, making it extremely difficult to diagnose the problem and caused a lot of confusion on my part and to the very kind photonsters who were very nice to help me with my problem. I got my main board from Anycubic and although, I haven’t had the time to test it out thoroughly yet, my first 3 prints since the main board replacement have been successful ?? .

The case of the mystery blob: Solved.
After 24 hours of almost non-stop printing and thru trials and many, many errors, I can now conclude that the blob was caused by 2 incompatible resins mixed together. What confounded this mystery was that at least one of the photonsters in this group, mixed the same kind of resins in similar percentages and yet got very good results. Thank you for the many Sherlock Holmes in this group for providing inputs and possible theories. Special mention to Sen Kun for his guidance and valuable insights. The 6th and finally successful print is a monocure calibration model downloaded from their website, using monocure rapid clear with the following settings: .040, 12, 2, 60, 6. Resins used resulting in blob (model was supposed to be a 20 mm XYZ cube) were anycubic gray with 20% Flex100. Lesson learned (at least for me) = only mix Monocure Flex100 with the same brand (Monocure Rapid).

翻譯年糕

How many hours does it take for the build plate to be elevated enough to check and see if the print stuck to it or not? How many hours does it take for the build plate to be elevated enough to check and see if the print stuck to it or not? 翻譯年糕

Update: The Blob Chronicle woes culprit was not resin related nor was it caused by defective LCD. It turns out my main board was faulty, giving intermittent output and variable results. Some times good prints but mostly failed prints including the blobs, making it extremely difficult to diagnose the problem and caused a lot of confusion on my part and to the very kind photonsters who were very nice to help me with my problem. I got my main board from Anycubic and although, I haven’t had the time to test it out thoroughly yet, my first 3 prints since the main board replacement have been successful ?? .

Mystery deepens. After finally getting the replacement LCD from Anycubic, I get this again. It’s supposed to be a 20 mm XYZ cube from Thingiverse, using Anycubic gray resin with 20% Flex100. The result is like a negative image of the cube. What a waste of expensive resin! Preview mode was alright. What’s next Sherlock Holmes of this Photon Group? Running out of hope here ? .

翻譯年糕