• COSPLAY 3D 建模
  • 3D列印服務
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Gareth Jones
2020-01-15 04:04:04

Hi all, had the printer for a while now and its great however I'm still struggling with layer lines on flat surfaces.

The bands are about 1mm apart.

I've tried the Z wob fix but it hasn't made any difference.

Any suggestions as to what to try next?

翻譯年糕

Corey Morrison
2020-01-15 04:05:18

Gareth Jones
2020-01-15 04:06:02

Corey Morrison
2020-01-15 04:06:35

William Riker
2020-01-15 04:07:01

Gareth Jones
2020-01-15 04:07:15

Corey Morrison
2020-01-15 04:07:36

Richard Humble
2020-01-15 04:09:15

Nipuna Gunarathne
2020-01-15 04:14:37

Gareth Jones
2020-01-15 04:17:57

Gareth Jones
2020-01-15 04:26:41

William Riker
2020-01-15 04:34:10


原文網址 Gareth Jones
2019-02-23 01:00:15

After a little help, been printing fine for a few weeks now. All of a sudden I have had a print fail, cleaned up beefed up supports and tried again still no luck.
I've levelled my bed tightened my FEP and its still failing.

I thought maybe its time to change the FEP but I've only used about 2L of resin and I've read people doing way more than that plus Interestingly the failure on the FEP is the full size of the screen like its exposing the whole bed, then the grip is too much for the plate?

Any ideas? bad file maybe?

翻譯年糕

Zena Andreou
2019-02-23 01:04:43

Philippe Maegerman
2019-02-23 01:08:30

Richard Shapiro
2019-02-23 01:53:20

Zena Andreou
2019-02-23 01:56:13

Eric Green
2019-02-23 01:57:10

Gareth Jones
2019-02-23 01:57:59

Gareth Jones
2019-02-23 01:58:55

Eric Green
2019-02-23 01:59:01

Gareth Jones
2019-02-23 02:00:15

Eric Green
2019-02-23 02:02:40

Gareth Jones
2019-02-23 03:05:43

Zena Andreou
2019-02-23 03:18:51

Gareth Jones
2019-02-23 03:25:30

Zena Andreou
2019-02-23 03:27:01

Gareth Jones
2019-02-23 03:28:06

Eric Green
2019-02-23 03:33:57

Gareth Jones
2019-02-23 03:52:27

Gareth Jones
2019-02-23 04:57:23

Zena Andreou
2019-02-23 04:58:18

Ivan Antharon Antalec
2019-02-25 16:15:32

Gareth Jones
2019-02-25 18:23:58


原文網址 Gareth Jones
2018-10-24 19:55:38

Hi all,

Had my photon for about 2 weeks now done a number of prints and while I'm really happy with the results, theyre not always as perfect as I would like but I get that I'm still learning.

The print last night has an issue with the Top? surface (the one closest to the build plate - is that top or bottom?)
It's lumpy and uneven, all other surfaces are perfect.
I even removed the supoports while washing it to make sure I cleaned off any surplus resin but it was already cured (at least partly).
Dont have any pictures with me unfortuntely but I can post one later.
The item is petty much a hollowed out cube approx 15mm.
I printed it at about 30 deg with the opening facing down (away from build plate)

Im going to try again tonight with a few different ways of placing the item on the buildplate, having read posts here for a while I have my theories as to why it happend but was hoping for some input from more experienced people.

My key thoughts are that

1. It was too close to build plate
2. Too shallow an angle / Bad orientation

If i have a hollowed cube can I print it with the hollow end attached tot he build plate? or will that cause problems when it prints the layer that will close it off? surely the hollwow would just fill with resin then?

Thansk for any help
Gareth

翻譯年糕


 

討論主題

全不選 常用關鍵字