Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Mortadella De Mortadellis
2019-04-10 16:37:43

Hi to all, I would have a question to ask to those who already found themselves with this problem.
I realized, as you can see in the photo, a series of buttons with inscriptions for a 50s vintage car radio.
The printing itself is not a bad thing, using Anycubic Gray Resin, but a number of problems have arisen, as shown in the photos.
In photo number 1, below, marked by the larger ellipses, I found that the floors are deformed, that is they tend to rise outwards, which also happens to me in all the prints. I explained it in photo number 3.
Moreover, again in photo 1, I have highlighted how the resin has exceeded between the upper and lower limits of the numbers and the edges of the buttons until it touches and covers the space that in reality should have been, as shown in the initial project of photo number 2.
The buttons have been printed full.
I have also noticed that by measuring with the gauge, both the width and the depth of each button, is exceeding by at least 0.3 mm.

These are the print settings:
Anycubic Resin Gray
Layer thickness: 0.05
Bottom exposure: 115 sec
Layer bottom: 8
Off time: 6.5 sec
Normal exposure: 18 sec
Ambient temperature, around 22 ° celsius

Anycubic Photon software.

If anyone can tell me some solution, I would be grateful.

翻譯年糕

Paul Churchill
2019-04-10 16:43:37

Mortadella De Mortadellis
2019-04-10 16:44:15

Ivan Antharon Antalec
2019-04-10 16:56:49

Luke Mason
2019-04-10 19:17:10

Robert Silvers
2019-04-10 21:20:12

Mortadella De Mortadellis
2019-04-11 01:14:54

Bradley VanScoyk
2019-04-11 09:44:34

Bradley VanScoyk
2019-04-11 09:47:06

Robert Silvers
2019-04-11 10:06:57

Devin Wallace Simonsen
2019-04-11 11:26:18

Dylan Hancox
2019-04-11 12:46:12

Mortadella De Mortadellis
2019-04-11 14:16:15

Breno Azevedo
2019-04-12 14:09:05

原文網址 Mortadella De Mortadellis
2019-03-24 20:51:07

Good morning everyone, I have a question for you. When I purchased the Anycubic Photon as a second test, I printed the eifell tour, then realized that the tower hung slightly towards the tip, with a gap of 2mm on one side (1mm + / - for the two opposite sides), the sides incriminated I believe they were on the X axis.
Then I re-leveled the printer with a level, but nothing to do, the error continues.
Do you know if there is a reliable test to be carried out, to check the verticality of the Z?

Thank you!

翻譯年糕

Mortadella De Mortadellis
2019-03-24 23:59:06

Dustin Skye
2019-03-25 00:48:54

Dustin Skye
2019-03-25 00:49:20

Mortadella De Mortadellis
2019-03-25 00:59:52

Dustin Skye
2019-03-25 01:16:44

Mortadella De Mortadellis
2019-03-25 01:18:20

原文網址 Mortadella De Mortadellis
2019-03-09 19:00:57

Hello everyone, I would have a question to ask those who may have already built something that I'm going to explain:
My idea is to create a containment chamber for the Anycubic Photon, in order to avoid breathing the toxic vapors of the resins during printing, and I would like, as well as having a vacuum cleaner, to maintain a constant temperature.
Some idea?
Thank you!

翻譯年糕

原文網址 Mortadella De Mortadellis
2019-02-17 21:41:29

Hello people, I made a mess, I wanted to try to do 2 side-by-side eiffel tours with 12-second exposure times during the night. This morning they were finished and I left them for about 3 hours in the 3D printer before detaching the pieces, which had come bad, with resin harnessed everywhere.
To detach them was a delirium, more on the floor remained touches of soldier resin, and in the vachetta, there remained a lot of soldered resin, partly on the FEP and partly on the metal of the pan. Now I have soaked in the IPA, there is the possibility of recovering at least the floor and the pan, that is to make them return clean or do I have to throw away everything and replace them?
Thank you!

翻譯年糕

David Nicholls
2019-02-17 22:00:47

Mortadella De Mortadellis
2019-02-17 23:27:11

David Nicholls
2019-02-18 00:20:03

Mortadella De Mortadellis
2019-02-18 00:28:37

Vinicius Silva
2019-02-18 19:00:31

Vinicius Silva
2019-02-18 19:01:30

Vinicius Silva
2019-02-18 19:03:05

原文網址 Mortadella De Mortadellis
2019-02-13 07:46:03

How to avoid the retraction of the resin, to avoid incorrect measurements of the models?
Can the supports help?

翻譯年糕

Robert Maefs
2019-02-13 07:46:32

原文網址 Mortadella De Mortadellis
2019-02-11 23:04:23

Ok, my third press, of which I am very satisfied, except for the external balustrade that is detached in several places.
The print is at 0.05 and the time layer at 10 sec.
Any ideas on the reason for the detachment of the external balustrade? The internal one is perfectly attached ,.
Thank you

翻譯年糕

Connor DjGlargum Whitesell
2019-02-11 23:26:56

Richard Shapiro
2019-02-11 23:32:32

Mortadella De Mortadellis
2019-02-12 01:10:13

Mortadella De Mortadellis
2019-02-12 01:11:44

Richard Shapiro
2019-02-12 01:11:51

Richard Shapiro
2019-02-12 01:12:00

Richard Shapiro
2019-02-12 01:12:15

Mortadella De Mortadellis
2019-02-12 01:14:05

Marco Zannini
2019-02-12 02:10:14

Marco Zannini
2019-02-12 02:12:25

Mortadella De Mortadellis
2019-02-12 02:13:06

Marco Zannini
2019-02-12 02:14:24

Marco Zannini
2019-02-12 02:15:42

Mortadella De Mortadellis
2019-02-12 02:17:26

Marco Zannini
2019-02-12 02:18:10

Mortadella De Mortadellis
2019-02-12 02:18:53

Adam Foster
2019-02-12 02:19:32

Marco Zannini
2019-02-12 02:20:16

Mortadella De Mortadellis
2019-02-12 02:20:40

Mortadella De Mortadellis
2019-02-12 02:21:26

Adam Foster
2019-02-12 02:23:23

Mortadella De Mortadellis
2019-02-12 02:24:30

Çağrı Aydoğan
2019-02-12 02:43:38

Mortadella De Mortadellis
2019-02-12 02:48:43

Susan Sioux Mercer
2019-02-12 06:27:43

Santiago Masdeu
2019-02-12 08:15:51

Mortadella De Mortadellis
2019-02-12 08:29:42

Per Bekker-Madsen
2019-02-12 17:37:44

原文網址 Mortadella De Mortadellis
2019-02-11 00:26:17

Hello everyone, a question for the more experienced, I noticed that the FEP, practically new, used only for 3 prints is already opaque, is it normal? When should it be replaced?
Thank you!

翻譯年糕

Sen Kun
2019-02-11 00:31:58

Sen Kun
2019-02-11 00:33:50

James Bricknell
2019-02-11 00:34:08

Sen Kun
2019-02-11 00:34:37

Sen Kun
2019-02-11 00:35:41

James Bricknell
2019-02-11 00:36:30

Sen Kun
2019-02-11 00:38:00

Nikolas Willingham
2019-02-11 00:38:55

Mortadella De Mortadellis
2019-02-11 00:40:05

Mortadella De Mortadellis
2019-02-11 18:03:06

Sen Kun
2019-02-11 18:26:06

Mortadella De Mortadellis
2019-02-11 18:29:37

原文網址 Mortadella De Mortadellis
2019-02-09 05:35:01

Ok, I did my second print test with this full printed Batman bust, at 2 cents per layer.
The print is 67 mm high and I wanted to keep the exposure times very low, Bottom 5 layer @ 40 sec. and 3 sec for layer.
I should have let it dry a little before dipping it in the IPA, because it was a bit 'too friable to the touch, however I am satisfied!

翻譯年糕