Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Timmo Hellemann
2019-07-07 22:35:14

What might have caused the slots? In the CAD model there is nothing special at this position. Of cause the walls are thin, but this is the same on other heights too. Any ideas?

翻譯年糕

Niall Forrester
2019-07-07 23:04:05

Stefan Giudici
2019-07-07 23:07:13

Timmo Hellemann
2019-07-07 23:10:00

Timmo Hellemann
2019-07-07 23:24:38

Stefan Giudici
2019-07-07 23:26:02

Timmo Hellemann
2019-07-07 23:34:03

Stefan Giudici
2019-07-07 23:35:47

Timmo Hellemann
2019-07-08 00:04:39

Timmo Hellemann
2019-07-08 00:07:15

Stefan Giudici
2019-07-08 00:15:48

Timmo Hellemann
2019-07-08 00:20:00

原文網址 Timmo Hellemann
2019-04-14 09:57:57

Anyone tried to print PCB solder stencils? Maybe the rough top surface might be some problem. But a stencil in 2 Minutes... think I have to try it

翻譯年糕

原文網址 Timmo Hellemann
2019-04-08 04:09:36

I wondered if the ventilation of the printing chamber is really necessary. And if so... why? I mean why blowing all the smelly fumes into my room?

翻譯年糕

Spencer Cook
2019-04-08 04:10:32

Alexander Wright
2019-04-08 04:17:52

Sen Kun
2019-04-08 04:20:27

Michael J Morris
2019-04-08 04:33:27

Timmo Hellemann
2019-04-08 04:35:36

Karlo Sanchez
2019-04-08 04:36:49

Breno Azevedo
2019-04-08 05:34:51

Susan Sioux Mercer
2019-04-08 05:37:12

Devin Wallace Simonsen
2019-04-08 11:44:24

Che Fielding
2019-04-08 19:16:05

Guti Gutmann
2019-04-08 20:05:13

Timmo Hellemann
2019-04-10 00:42:42

Karlo Sanchez
2019-04-10 01:37:56

原文網址 Timmo Hellemann
2019-04-07 22:21:55

Memory Error M_100000.
So I already printed a couple of times without any problems.
Today I wanted to print again but when I plugged in the original USB-Stick I got the error. I then formated the Stick again with FAT32 but still the same. Then I tested my SandDisk 8 GB stick and this worked at the beginning. But after four layers I got the error again and it stopped printing.
Any ideas?

翻譯年糕

Michael J Morris
2019-04-07 22:22:40

Michael J Morris
2019-04-07 22:23:36

Jean-François Meloche
2019-04-07 22:26:49

Michael J Morris
2019-04-07 22:28:53

Michael J Morris
2019-04-07 22:29:08

Jean-François Meloche
2019-04-07 22:29:44

Timmo Hellemann
2019-04-07 22:30:02

Jean-François Meloche
2019-04-07 22:30:06

Michael J Morris
2019-04-07 22:30:38

Jean-François Meloche
2019-04-07 22:39:03

Michael J Morris
2019-04-07 22:40:20

Lane Taylor
2019-04-07 22:40:41

Timmo Hellemann
2019-04-07 23:15:53

Jean-François Meloche
2019-04-07 23:28:11

James Cachia-Garrett
2019-04-08 17:25:20

Timmo Hellemann
2019-04-10 00:29:49

Steve McGuigan
2019-07-12 23:38:08

Cale Milligan
2019-07-12 23:50:27

Tino Mack
2019-08-02 23:26:01

Cale Milligan
2019-08-03 01:50:53

原文網址 Timmo Hellemann
2019-03-31 06:35:53

So I had a problem on my last print. as you see the first layers are complete, after a couple of layers only half of the models are printed.
When the print was finished I started the UV-Test via the Menu and there also was only half of the screen illuminated. After I powered off the Printer and did the test again, everything was fine?!
Any suggestions what might happened?

翻譯年糕

Stefan Giudici
2019-03-31 06:56:22

Mark Wardle
2019-03-31 07:25:57

Jake Larson
2019-03-31 07:29:32

原文網址 Timmo Hellemann
2019-03-31 03:03:49

Is there a way to look at the printed parts to see if everthin adheres properly to the bed while it is printing and not have to wait ~3 hours until the lift movement shows the parts a little bit?

翻譯年糕

Israel Francisco
2019-03-31 03:05:39

Philippe Maegerman
2019-03-31 03:05:41

Timmo Hellemann
2019-03-31 03:06:29

Mark Wardle
2019-03-31 03:07:58

Stefan Giudici
2019-03-31 03:38:21

Timmo Hellemann
2019-03-31 04:03:15

原文網址 Timmo Hellemann
2019-03-28 07:25:13

So I just got the Photon for a good price (310€). Benchy printed well but I had problems with a ring (Thing 35803). Slicer vs Print... I'm new in SLA/DLP, maybe I did something wrong with the supports? Layer height was 0.03mm, exposure time 6s. Benchy was on the same bed and printed well.
I didn't find any small exposed parts in my storage container

翻譯年糕