Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Sein Saini
2019-06-14 17:07:58

Is it the best orientation? 3 times failed print.

翻譯年糕

Dennis Kratzer
2019-06-14 17:14:07

Zena Andreou
2019-06-14 17:25:37

Sein Saini
2019-06-14 17:33:22

Dennis Kratzer
2019-06-14 17:36:37

Wade Peek
2019-06-14 18:05:28

Amerigo Galeotti
2019-06-15 09:32:11

Scott Peterson
2019-06-15 12:18:24

Chris Wood
2019-06-15 17:52:22

Devin Wallace Simonsen
2019-06-15 20:02:43

Mike Swanson
2019-06-16 00:36:17

Devin Wallace Simonsen
2019-06-16 02:27:06

原文網址 Sein Saini
2019-06-14 09:48:58

Hi guys, can anyone tell me how to improve the support affect? actually it is a flat part..

翻譯年糕

Eric Wilfreesboro
2019-06-14 09:50:41

Adam Horton
2019-06-14 10:31:40

原文網址 Sein Saini
2019-06-03 16:21:29

Hi guys, anyone know where can i purchase anycubic green..and deliver to Malaysia?

翻譯年糕

Alexius Lim
2019-06-03 16:24:05

Sein Saini
2019-06-03 17:17:27

Alexius Lim
2019-06-03 17:18:46

原文網址 Sein Saini
2019-05-24 21:45:35

Guys, i need your help..when i want to set z = 0, the bed was not level when i pressed down 0.1..the front part of the bed will be tilt a bit..the back part of the bed will hit the lcd screen first..i need to find what is the causes of this issue.mplease help me

翻譯年糕

Maik Nolte
2019-05-24 21:49:09

Sein Saini
2019-05-24 21:50:24

Philippe Maegerman
2019-05-24 21:51:28

Sein Saini
2019-05-24 21:52:54

Philippe Maegerman
2019-05-24 21:53:54

Sein Saini
2019-05-24 21:55:26

Philippe Maegerman
2019-05-24 21:58:40

Andrew Chan
2019-05-24 22:34:35

Chad Elstad
2019-05-24 23:44:16

Philippe Maegerman
2019-05-24 23:50:46

Sein Saini
2019-05-24 23:55:43

Philippe Maegerman
2019-05-24 23:58:52

Sein Saini
2019-05-24 23:59:48

Adam Horton
2019-05-25 09:59:10

Dominick Trascritti
2019-05-25 20:58:46

Travis McGeathy
2019-05-26 02:14:16

原文網址 Sein Saini
2019-05-18 10:58:30

Guys, im trying to print flat part direct to the bed. But the the thickness of the bottom part is not same as actual part..it is quite thinner compare to the actual part..is anyone know how to improve the print as i need to print it flat, to reduce support material?

翻譯年糕

Danny Lloyd
2019-05-18 12:24:07

Stephen Farrell
2019-05-18 17:31:26

原文網址 Sein Saini
2019-05-12 09:39:00

Anyone know on how to reduce support affect? Now im using anycubic green resin..does anyone have best setting for the resin?

翻譯年糕

Danny Lloyd
2019-05-12 17:27:05

Gary Houser
2019-05-14 20:31:44

Gary Houser
2019-05-14 23:16:14

原文網址 Sein Saini
2019-05-09 09:15:25

Hi guys, could anyone suggest to me the best setting for anycubic black? my print always stuck at fep

翻譯年糕

Dennis Back
2019-05-09 09:40:28

Kelly Rinaldi
2019-05-09 10:24:25

Bob Deblier
2019-05-09 11:20:16

Sein Saini
2019-05-09 11:24:55

原文網址 Sein Saini
2019-04-26 16:47:39

Hi guys, i have failed many times to print the part. The radius always not properly formed. Anyone have any ideas to print this part. i have tried to print the part in 45 degree angle and used heavy support anycubic photon slicer

翻譯年糕