Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Nick Chicone
2019-11-14 23:44:37

Does anyone have tips on getting a model that has been printed flat on the build plate off? The scrapers I've got from my photons are all tore up. Thanks!

翻譯年糕

Eric Pribish
2019-11-14 23:46:31

Hugh Jeriolas
2019-11-14 23:47:04

Scott Pavlich
2019-11-14 23:47:04

Derek Reihe
2019-11-14 23:47:37

Blake Roney
2019-11-14 23:48:45

Eric Pribish
2019-11-14 23:49:00

Eric Wilfreesboro
2019-11-14 23:49:52

Joel Mendoza
2019-11-14 23:50:28

Zena Andreou
2019-11-14 23:52:32

Francis X Benz
2019-11-14 23:52:47

Stefan Giudici
2019-11-14 23:58:54

Joey Pruitt
2019-11-15 00:02:11

Ethan Williams
2019-11-15 00:03:29

Ironi R Johnson
2019-11-15 00:07:54

Jim Nelson
2019-11-15 00:27:12

Nick Chicone
2019-11-15 00:28:44

Chris Edrington
2019-11-15 00:36:13

Alex Dodge
2019-11-15 00:44:00

Simon Wilson
2019-11-15 00:46:40

Francis X Benz
2019-11-15 00:49:06

Joey Pruitt
2019-11-15 00:58:41

Simon Wilson
2019-11-15 01:03:49

Joe Lewis
2019-11-15 04:59:16

Polly Jackson
2019-11-15 05:13:52

Peter Ede
2019-11-15 05:25:14

原文網址 Nick Chicone
2019-08-18 07:47:46

I found the settings for the Siraya blu to program my printer too. However I cant find any info on if I actually need a heater for the inside of my photon or not. Thoughts?

翻譯年糕

Stefan Giudici
2019-08-18 07:51:27

Nick Chicone
2019-08-18 07:52:10

Nick Chicone
2019-08-18 08:00:32

Jon Carroll
2019-08-18 08:10:25

Nick Chicone
2019-08-18 08:11:13

Scott Pavlich
2019-08-18 08:30:02

Mike Fatchett
2019-08-18 08:42:25

Nick Chicone
2019-08-18 10:23:06

原文網址 Nick Chicone
2019-08-15 01:47:05

Hello everyone, I've searched just about everywhere for the solution and havent found it. My photons are correctly leveled, there is no z wobble, and I have had a very high success rate with using rafts. All of a sudden the rafts end up being skewed/angled instead of being all one evenly solid piece. Which results in some of the pieces I print with supports to be stuck in the raft. In the photon slicer I double check everything and I cannot figure out why the rafts are coming out skewed with some parts being stuck in them. I've even been moving the models up to 5mm above the build plate in the slicer and still the pieces come out with very short supports...the slicer preview doesn't seem to be accurate or something. Also have had an unfortunate amount of failures using this new bottle of the anycubic resin in black...was thinking it could be the resin. Thanks!

翻譯年糕