Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Ewan Harwood
2019-10-21 01:42:38

So I've re-levelled, tightened the FEP to 320Hz, upped the angle and the amount of supports, took the thing apart and made sure the z axis eccentric nut was tight (it was already tight the hole way up and down the axis) and I'm still getting annoying random lines appearing! Any other ideas? Is it possible the z axis is too tight? Meaning there isn't smooth movement? That's the only thing I can think of at this stage.

翻譯年糕

Aleksey Kulagin
2019-10-21 01:47:20

Ian Chess
2019-10-21 01:50:27

Phillip Kenney
2019-10-21 01:53:23

Matt Hooton
2019-10-21 01:55:34

Ewan Harwood
2019-10-21 01:56:12

Ewan Harwood
2019-10-21 01:56:49

Ewan Harwood
2019-10-21 02:23:51

Matt Hooton
2019-10-21 02:33:05

Kelly Filgo
2019-10-21 04:41:00

Ewan Harwood
2019-10-21 06:25:38

Brad Herman
2019-10-21 09:23:41

Aleksey Kulagin
2019-10-24 16:23:57

原文網址 Ewan Harwood
2019-10-15 04:32:42

So what's the deal here then knowledgeable people? Horrible lines up to about 4cm or so then it's perfect (apart from me knocking the antenna off when removing supports). Is this Z-wobble? Dodgy z screw?

翻譯年糕

Quinn Mehling
2019-10-15 04:40:47

Ewan Harwood
2019-10-15 04:43:48

George Bulte
2019-10-15 04:46:14

Joshua Collins
2019-10-15 04:46:15

George Bulte
2019-10-15 04:48:36

Quinn Mehling
2019-10-15 04:48:37

Quinn Mehling
2019-10-15 04:50:20

Ewan Harwood
2019-10-15 04:53:12

Ewan Harwood
2019-10-15 04:58:24

Ewan Harwood
2019-10-15 04:59:33

Scott Smith
2019-10-15 05:01:34

Ewan Harwood
2019-10-15 05:09:43

Scott Smith
2019-10-15 05:11:45

Ewan Harwood
2019-10-15 05:16:21

Ewan Harwood
2019-10-15 05:16:37

Scott Smith
2019-10-15 05:17:23

Chad Elstad
2019-10-15 05:26:15

Joshua Collins
2019-10-15 05:47:31

Joshua Collins
2019-10-15 05:49:43

Joshua Collins
2019-10-15 05:52:20

Ewan Harwood
2019-10-15 06:13:56

Richard Allsebrook
2019-10-15 06:38:30

John Giardino
2019-10-15 09:56:29

Stefan Giudici
2019-10-15 10:38:06

Joe Broggio
2019-10-15 11:13:12

Ewan Harwood
2019-10-15 15:41:30

John Giardino
2019-10-15 20:20:10

Jerry Little
2019-10-16 05:17:04

原文網址 Ewan Harwood
2019-10-05 19:43:33

First proper print, engines for Serenity from firefly, but what's that wave effect on the right hand side? Both printed together but seems worse on one. Z axis wobble? Need to print again anyway in a different resin, this was just a test to see if the supports worked. They kinda did but room for improvement definitely.

翻譯年糕

原文網址 Ewan Harwood
2019-10-01 21:43:18

Hey all, so my Photon is arriving today and I had planned to use it in my workshop shed but I've just been reading about the temperature affecting prints, so is it a no-go to have it in an uninsulated environment? I'm in Scotland so it can get quite cold over the winter, I heat the workshop when I'm in it but would expect to leave the printer running. Am I going to have to incur the wrath of the wife and put it inside somewhere?

翻譯年糕

Rastko Stanojevic
2019-10-01 21:47:31