• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Ðam's Voué
2020-03-21 21:36:29

Well, how im i supposed to interprete a nearly invisible exposure test... Not enough Time? All are pretty empty, and the total thickness is less than a milimeter

翻譯年糕

Jason Willis
2020-03-21 21:47:10

Is the rest stuck to the fep?

Ðam's Voué
2020-03-21 22:03:24

Jason Willis nothing on the fep, i see sommes details, but i have to look hard with sun reflection

Jason Willis
2020-03-21 22:05:57

It's likely the wrong base exposure times for your resin then. Try adding a little time to it all and see if it makes a difference

Tiernan Messmer
2020-03-21 22:07:48

Did you wash and cure it? I find taking it off the plate can make it easier to read too. That said clear resins don't work as well with the exposure test too

Ðam's Voué
2020-03-21 22:10:16

well, it's a rapid resin, said 5-15 sec on the box, (and i used the same resin in red with awesome results, it's eleego abs like translucent), so i'm a bit confused

Jason Willis
2020-03-21 22:11:26

Ðam's Voué light transfers through different pigments at different rates. Clear doesn't absorb as much as quickly

Ðam's Voué
2020-03-21 22:14:58

Jason Willis so i should try more than 20 sec then? it's weird, i used 5 sec on the red translucent, and this one should have same (according to eleego) settings, maybe my z=0 is too low? and i have not enough room?

Jason Willis
2020-03-21 22:19:04

Ðam's Voué z=0 to low would only limit you on the base portion of the build. The rest should print normally when you get farther in or it would be stuck to the fep.

What are your base times set to? What was the rest of the prints exposure time?

Ðam's Voué
2020-03-21 22:25:32

yeah, still nearly invisible, but i can see the "timer" on each, i'm confused because it's supposed to be 5-15 sec, and the test run 2-20is this supposed to be that thin?

Tiernan Messmer
2020-03-21 22:26:57

Err the numbers go from 1-10, and you double the numbers to get the time (eg column 1 is 2 seconds, column 7 is 14 seconds). What's the name of the file you printed?

Ðam's Voué
2020-03-21 22:28:50

i used the test from this group, and since it's a rapid resin i used the rapid resin test; base 100 sec, 20 micron 2-20 sec

Ðam's Voué
2020-03-21 22:29:39

Tiernan Messmer resin-test-20u.B100.2-20, from the resin test i took in this group

Tiernan Messmer
2020-03-21 22:32:25

Yeah that file is what I was describing. Not sure where you got the idea it was meant to be 5-15s from? The 2s to 20s is what the 2-20 means in the filename.

Ðam's Voué
2020-03-21 22:35:36

Tiernan Messmer the 5-15 range is for this resin, from the box :) so i tought 2-20 could cover more than necessary tests

Tiernan Messmer
2020-03-21 22:36:48

Ohh I follow now. And yes it's meant to be thin. But yeah clear resins are hard to read

Ðam's Voué
2020-03-21 22:37:02

Ðam's Voué
2020-03-21 22:37:41

Tiernan Messmer more than hard, all test are flat, so i tought i did something wrong

Ðam's Voué
2020-03-21 22:40:52

the fact is, few month ago i did lot of awesomes prints, different kind of size and type of prints, i made a pause for 2 month (had a lot to do, and somes paints) and now, nothing work anymore.. i failed 20 prints in a week, with weird somes supports breaking in the middle or stopping at the end of support, with the print don't attached to it (but only on somes randoms supports) so i try another bottle of resin, in case for some reason my resin is corrupted, but i can't even get a good exposure test...

Ðam's Voué
2020-03-21 22:41:41

since all my problems were only bed leveling, and finding the good exposure time, i don't have much experience in problems resolutions, and i need help from people with more knowledge


原文網址 Ðam's Voué
2020-03-20 01:27:34

Now i don't get it, supports fails in the middle.... And sommes fails the exact moment they should be attached to print, but not everytime, can it be corrupted bottle? It was keept under 20°, no UV, but oppened 2 month ago (and i didn't print with for this period) i don't remember issues with this resin before that

翻譯年糕

Stuart Johnson
2020-03-20 01:28:20

Is it coming away from the plate? That seems like it might be an issue.

Wes Shawshank Crain
2020-03-20 01:31:17

Im having this same damn issue and im seeing multiple posts a day about it... May I ask were you having success before with the same resin and times and such

Ðam's Voué
2020-03-20 02:29:31

somes work perfectly, and somes just don't attach the print, the raft and the supports attached to the raft are ok, the structure seem's to be ok, but somes supports just don't work (and few stop in the middle...)

Ðam's Voué
2020-03-20 02:35:09

Wes Shawshank Crain yes i've done more than 60 mini with this resin, and some with the same bottle already, i tryed on the 2 last try to use the "Big" supports (in case my resin is just brittle for an unknown reason) and this wasn't the solution obviously

Wes Shawshank Crain
2020-03-20 03:33:47

So im in the same boat I was having dramatic success then random failures and im wondering if its a software issue

Ðam's Voué
2020-03-20 04:17:26

Wes Shawshank Crain then Can it be chitubox? I'll try to down the version and try again, but i'm bored of loosing Time and resin

Wes Shawshank Crain
2020-03-20 05:25:29

Ðam's Voué i use prusa slicer for supports and slice in photon so maybe a firmware

Ðam's Voué
2020-03-21 07:43:12

Stuart Johnson if you talk about the space between the raft and the bed, there isn't any, it's the translusence, raft is well attached to the bed( 3 more try today, still not working, tryed with chitubox ou prusaslicer supports, for tonight i try a new bottle of resin, because that's the last thing i can try tbh)


原文網址 Ðam's Voué
2020-03-16 03:24:30

4 prints in a row failed, leveled the bed each time, i have prints only on the corners, on the last print the raft was thinner in the center (and everything failed), so i guess i have to change my FEp, since i can't thight it anymore, and it has somes marks (i can feel them with my finger, that's not only cloudish), what should i look for on amazon?

翻譯年糕

Brendan Wood
2020-03-16 03:27:24

If there's no hole you don't need to change the FEP. It can get pretty darn cloudy and marked before needing a change. What are your exposure settings? It sounds like your base layers might be too low

Ðam's Voué
2020-03-16 03:29:18

Already got lot of succesfull print with my settings

Ðam's Voué
2020-03-16 03:30:36

There is no hole

Ðam's Voué
2020-03-16 03:33:00

Here we can see the thinner raft in the center, i had all my raft printer, and most of it attached to the bed, but the supports failed on different levels, i don't really understand what's happening tbh

Ðam's Voué
2020-03-16 03:33:55

Brendan Wood and since i have"pinch" (ish) on my fep, and the center is looser, i tought it could be the problem

Brendan Wood
2020-03-16 03:35:53

The thin part is because there is not enough time on large prints for the resin to flow from the edges to the center when the bed raises. You can try increasing the raise distance or give it a pause and temperature plays a role here.

Merv Hinton
2020-03-16 05:20:52


原文網址 Ðam's Voué
2020-03-14 22:07:44

Does that look like supports issues ? All 4 corners are perfect, all others parts failed... Maybe fep tension ? What else could it be?

翻譯年糕

Logan Lees
2020-03-15 00:11:09

https://www.prusa3d.com/3d-print-quality....../ looks to me like either settings, or support issues. Do the supports in Prusa Slicer, and slice it in chitubox

Tom Sargison
2020-03-16 05:29:59

Check out my Newbie resin printing guide it may be usefull for you to master supports and more
https://www.facebook.com/groups/AnycubicPhoton/permalink/1959611750850124/

Ðam's Voué
2020-03-16 05:44:14

the problem is that i already printed 60ish miniatures, i make a pause to paint, and now everything is trash, i obviously leveled the bed between each failed print, i'm currently testing soething, i heard the good old succion sound, that's already a good point, i'll see in 9 hours if my screamers are fines

Ðam's Voué
2020-03-17 18:48:15

Ðam's Voué
2020-03-17 18:54:48

Tryed Big and middle supports in chitubox, and supports with prusaslicer, all little things print, but i don't understand, i'm sure this is supports problem, since supports print correctly, but the print don't attach to it, what else Can it ne? I've printed dozens on mini with same or little supports without issue, and now i'm stuck with fails...


原文網址 Ðam's Voué
2019-12-07 20:33:48

So, i Guess the 6 second (collumn 3) is good, but what's the meaning of the "clear" zone is the center? (Sorry for sun reflection, but with this transparent resin it's invisible otherwise)

翻譯年糕

Nipuna Gunarathne
2019-12-07 21:14:08

Ðam's Voué
2019-12-07 21:20:02


原文網址 Ðam's Voué
2019-12-05 01:31:01

So, how can i get rid of support marks? (Chitubox settings bellow, i'll screen with pc for lisibility)

翻譯年糕

Ðam's Voué
2019-12-05 01:33:36

Ðam's Voué
2019-12-05 01:33:46

Nick Taylor
2019-12-05 01:37:39

Ðam's Voué
2019-12-05 01:47:33

Nick Taylor
2019-12-05 01:55:48

RIcardo Castillo
2019-12-05 02:01:04

RIcardo Castillo
2019-12-05 02:01:27

Paul West
2019-12-05 02:08:12

Ðam's Voué
2019-12-05 02:09:54

Ðam's Voué
2019-12-05 02:12:25

Christian Mendez
2019-12-05 02:14:41

RIcardo Castillo
2019-12-05 02:18:26

Paul West
2019-12-05 02:32:38

Ðam's Voué
2019-12-05 03:17:21

Paul West
2019-12-05 03:24:40

Robert Hamberger
2019-12-05 05:00:24

Paul West
2019-12-05 07:21:59

Paul West
2019-12-05 07:22:03

Zäta Doe
2019-12-05 14:07:07

Zäta Doe
2019-12-05 14:08:52


原文網址 Ðam's Voué
2019-12-02 08:15:49

The first guy had his feets melted to the raft, the second one didn't get a raft (but printed perfectly) i got somes accessoires where 5 mm down disapeard in bed, and others perfectly fine. All that on the same print, and with no logic placement (the one without raft was at centre, the one without feet in a corner and the 3 backpacks was separated) so i have to ask, wth is going on here ?

翻譯年糕

Ðam's Voué
2019-12-02 08:18:00

Justin Lincoln
2019-12-02 09:07:57

Ðam's Voué
2019-12-02 21:14:01


原文網址 Ðam's Voué
2019-11-30 02:09:04

Sound like a bed leveling problème right? But it started to snap to the bed everywhere, i am really supposed to level bed every few prints ? Since i have the elegoo red resin i have lots of fails, i probably need to adjust settings but no clue in wich direction i should work

翻譯年糕

Sherri Leyden
2019-11-30 02:19:05

Ðam's Voué
2019-11-30 05:41:56


原文網址 Ðam's Voué
2019-11-24 04:35:37

i need some help, i've bought my second resin (Elegoo res transparent) and tryed my first print, the bed is correctly leveled (i've did it just before the print) but it didn't snap to the bed, it was snap to the FEP, i think it's the settings, so here a pic of what i did, i obviously missed something (yes i checked the google doc, line 78)

翻譯年糕

Zachary Chin
2019-11-24 04:53:16

Ðam's Voué
2019-11-24 05:10:54

Zachary Chin
2019-11-24 05:20:31

Ðam's Voué
2019-11-24 05:35:09

Zachary Chin
2019-11-24 05:37:16

Ðam's Voué
2019-11-24 05:46:57

Zachary Chin
2019-11-24 08:52:51

Ðam's Voué
2019-11-26 04:43:40

Ðam's Voué
2019-11-26 04:49:43

Zachary Chin
2019-11-26 04:58:11

Ðam's Voué
2019-11-26 07:03:32


原文網址 Ðam's Voué
2019-11-21 16:52:35

I've read contradictory things about IPA and curing, i'm pretty sure that's not good to bath resin in IPA for 30h, but what's the limit? I often let my miniatures for 60-120 minutes (because i'm working with kids and don't want to take risks) in their bath, or in UV lamp, should i let them in a dark place and clean/cure later?

翻譯年糕

Bernardy L
2019-11-21 16:56:44

Ðam's Voué
2019-11-21 17:02:31

Andrew Springer
2019-11-21 17:05:12

Tiernan Messmer
2019-11-21 17:07:48

Ðam's Voué
2019-11-21 17:10:56

Andrew Springer
2019-11-21 17:12:39

Dennis Juel Jørgensen
2019-11-21 17:21:43

Andrew Springer
2019-11-21 17:23:46

Paul Churchill
2019-11-21 17:37:54

Tiernan Messmer
2019-11-21 17:40:56

Andrew Springer
2019-11-21 17:45:17

Andrew Springer
2019-11-21 17:45:39

Patrick Haeflinger
2019-11-21 18:10:37

Andrew Springer
2019-11-21 18:28:19

David Collinson
2019-11-21 18:42:50

David Collinson
2019-11-21 18:44:06

Patrick Haeflinger
2019-11-21 18:46:17

Andrew Springer
2019-11-21 18:46:47

David Collinson
2019-11-21 18:52:02

Serin Jameson
2019-11-21 18:55:01

David Retske
2019-11-21 19:56:21

Ðam's Voué
2019-11-21 20:31:15

Eric Green
2019-11-21 21:36:47

Robert Hamberger
2019-11-21 23:07:33

Angelo Apostolou
2019-11-22 08:19:42

Jarin Udom
2019-11-22 08:43:11

Dave Dewees
2019-11-22 08:45:05

Tiernan Messmer
2019-11-22 13:04:58

Tiernan Messmer
2019-11-22 13:06:27

Serin Jameson
2019-11-22 13:10:06

Jared Zadorozny
2019-11-23 02:21:29


 

討論主題

全不選 常用關鍵字