Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Gaze Hound
2020-03-31 11:43:20

since i can not use chitubox any more any other programs people recommend for doing supports and slicing

Chris Peck
2020-03-31 11:48:06

Why can’t you use Chitubox?

Gaze Hound
2020-03-31 11:52:04

Chris Peck finished doing supports on project loaded up next project and was blank no rectangle for work area and no part. loaded part i just finished would not load ether not worked since. did a reinstall and still dont work.

Chris Peck
2020-03-31 12:22:33

Oh dang. That sucks. I know it has a few less settings/features but have you tried using the photon workshop yet? I have been using chitubox for all my supports and such and then I have to use photon to slice because Chitubox doesn’t support the photon zero yet.

Gaze Hound
2020-03-31 12:36:10

up till to day it was all i was using too. i can not get the support right in workshop but was going to be tring it again

原文網址 Gaze Hound
2020-03-30 15:43:36

has any one had the problem of chitubox not showing the work area or the part? i just finished one project went to load new project and screen went blank. went back to one just finished and would not load ether. tried to uninstall and reinstall but still did not work

翻譯年糕

原文網址 Gaze Hound
2020-02-14 14:50:45

seeing if someone could explain these settings

bottom lift speed
lifting speed
bottom light off delay
light off delay

翻譯年糕

Chris Holden
2020-02-14 17:15:38

Mike Tate
2020-02-14 17:59:34

Sander van Deijl
2020-02-14 18:15:37

Andrew Steel
2020-02-14 21:48:21

原文網址 Gaze Hound
2020-01-29 00:08:30

is there a town exposure test for the photon that lets you do multiple at the same time

翻譯年糕

Stefan Giudici
2020-01-29 00:16:25

Gaze Hound
2020-01-29 00:17:53

Tom Franco
2020-01-29 00:18:40

Gaze Hound
2020-01-29 00:19:39

原文網址 Gaze Hound
2020-01-27 13:11:18

what causes this distortion see it as a line at bottom of the town and side with checker board is missing a line the other piece i know have a lot of supports yo clean still but the side faceing the bed always looks like it is melted. but rest of the print is dimensionally accurate

翻譯年糕

Gaze Hound
2020-01-27 13:13:27

Luke Pettit
2020-01-27 14:19:56

David McGyver
2020-01-27 19:41:19

Gaze Hound
2020-01-28 01:14:55

原文網址 Gaze Hound
2020-01-22 03:50:55

what is best program for adding supports to a model. been using chitubox but it is wanting to put supports on the model filing detail instead of doing them to a long support next to it

翻譯年糕

Ryan Shelvik
2020-01-22 03:53:07

Gaze Hound
2020-01-22 03:54:32

Ryan Shelvik
2020-01-22 03:56:44

Gaze Hound
2020-01-22 03:58:33

Gary Houser
2020-01-22 03:59:01

Ryan Shelvik
2020-01-22 04:02:07

Scott Dimmick
2020-01-22 04:04:21

Gary Houser
2020-01-22 04:05:12

Gary Houser
2020-01-22 04:07:56

Jason Pedersen
2020-01-22 20:25:08

原文網址 Gaze Hound
2020-01-20 05:33:05

had a question on this shift in my prints it does not fo this all the time and i have my part off the build plate but on the side cloest to the build plate i get this like shift

翻譯年糕

原文網址 Gaze Hound
2020-01-19 12:43:48

how far off of the bed do you normally place a part? i been running into problem of when i put it flat on plate of off a little it get to were it won't let me put any bracing

翻譯年糕

Matthew Steeghs
2020-01-19 12:56:56

Андрей Шестаков
2020-01-19 13:08:08

原文網址 Gaze Hound
2020-01-12 06:58:42

see if can get a question answered on the photon file validator on the the islands what is biggest island you need to support. i know 1 and 2 pixel not to mess eith but what about 5 or 10 pixel

翻譯年糕

原文網址 Gaze Hound
2020-01-12 00:02:16

finally have my printer dialed i think have done 2 prints full detail and no deformation

翻譯年糕