Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Ryan Ryan
2020-03-01 06:05:09

Anyone here good with Mesh Mixer? I found an amazing model online with a great quality STL but a few pieces are too big for my Photon. And I'm having serious trouble with the plane cut feature. Help?

翻譯年糕

Derek Reihe
2020-03-01 06:14:30

Ryan Ryan
2020-03-01 06:21:49

Joseph Brancik
2020-03-01 06:28:48

Zeb Christmas
2020-03-01 06:35:27

Ryan Ryan
2020-03-01 06:40:05

Joseph Brancik
2020-03-01 06:44:15

Joseph Brancik
2020-03-01 06:45:49

Fred Bey
2020-03-01 07:23:44

Joseph Brancik
2020-03-01 07:28:43

Aris Maragoudakis
2020-03-01 07:29:24

Rick Hanson
2020-03-01 07:39:43

Joseph Brancik
2020-03-01 07:41:15

Landon Alumbaugh
2020-03-01 07:47:19

Ryan Ryan
2020-03-01 07:48:27

Ryan Ryan
2020-03-01 07:48:45

Derek Reihe
2020-03-01 07:54:37

Joseph Brancik
2020-03-01 07:59:59

Derek Reihe
2020-03-01 08:01:00

Joseph Bushen
2020-03-01 08:05:30

Bill Keeter
2020-03-01 08:16:01

Richard Pigott
2020-03-01 08:47:02

Landon Alumbaugh
2020-03-01 08:51:56

Vincent Balmont
2020-03-01 08:58:38

Chris Wolfe
2020-03-01 10:00:24

Chris Roberts
2020-03-01 10:19:32

Ryan Ryan
2020-03-01 10:30:32

Janus Stark
2020-03-01 17:53:47

James Cachia-Garrett
2020-03-01 21:18:25

Ken Schmitt
2020-03-01 22:27:02

Ryan Ryan
2020-03-02 00:57:47

Jacobus Canjels
2020-03-02 02:30:17

Ryan Ryan
2020-03-02 09:00:26

Chris Holden
2020-03-02 15:38:04

Brett Hogan
2020-03-02 23:04:17

原文網址 Ryan Ryan
2020-02-18 11:39:22

Im having a problem where the print doesn't stick to the build plate. I just get these flat little chips I have to peel off the resin bath screen. I'm using the suggested exposure times, taken from the clear green elegoo resin bottle, 60 seconds bottom layer, 8 seconds normal layers. And yes, I trammed the build plate yesterday.

翻譯年糕

Brian JH
2020-02-18 11:43:45

Ryan Ryan
2020-02-19 09:57:24

Brian JH
2020-02-19 10:07:30

Ryan Ryan
2020-02-19 11:40:50

Brian JH
2020-02-19 11:56:58

Ryan Ryan
2020-02-20 02:29:57

Brian JH
2020-02-20 02:33:17

Ryan Ryan
2020-02-20 02:33:46

Brian JH
2020-02-20 03:10:15

Ryan Ryan
2020-02-20 12:08:42

Brian JH
2020-02-20 12:28:14

Ryan Ryan
2020-02-20 12:34:47

Brian JH
2020-02-20 12:51:21

原文網址 Ryan Ryan
2019-12-25 02:22:27

Trying to print this pokeball shell but the first time it failed and warped from (what I assume was) only having two supports on the low points. So I added the ones you see here and now it fails and does not stick to the build plate and ends up in the resin bath as a flat chip... help?

翻譯年糕