• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Lorne Bixby
2020-03-10 22:35:16

So i have a print paused and need to add resin... Started with anycubic grey just got elegoo grey...
Looked at the photonsters settings and they look close, any issues with this ?

翻譯年糕

Jonathon Michael Starwalt
2020-03-10 22:36:55

Robert Jeppesen
2020-03-10 22:40:43

Robert Jeppesen
2020-03-10 22:41:06

Scott Pavlich
2020-03-10 22:41:43

Lorne Bixby
2020-03-10 22:44:33

Ruben Smit
2020-03-10 22:53:43

Lorne Bixby
2020-03-10 23:23:44

Bruno Tabarani
2020-03-10 23:39:22


原文網址 Lorne Bixby
2020-02-29 21:25:14

Has anyone found a way to raise the platform higher when pausing a print...
It pauses so low i can't see the back side of the build plate.
I don't dare remove the plate, lest it doesn't sit exactly where it was when i put it back.

Just had a 15 hour print continue all night a failure i couldn't see.

翻譯年糕

David Newton
2020-02-29 21:48:42

Lorne Bixby
2020-02-29 21:50:25

David Newton
2020-02-29 21:52:02

Lorne Bixby
2020-02-29 21:54:23

Lorne Bixby
2020-02-29 21:54:38

Lorne Bixby
2020-02-29 21:55:00

David Newton
2020-02-29 21:55:08

David Newton
2020-02-29 22:01:33

Lorne Bixby
2020-02-29 22:03:18

Paul 'Jam' Morris
2020-02-29 22:07:07

David Newton
2020-02-29 22:19:22


原文網址 Lorne Bixby
2020-02-29 21:01:06

Does anyone know what might cause this type of mid plate shearing ?
Well supported, run through validator. No islands.
My prints have been dialed in and great lately.
Fep in good condition.
Anycubic grey
.04 layer height
14s exposure
10 layers bottom @ 120 seconds

翻譯年糕

Casey Frank
2020-02-29 21:03:57

Lorne Bixby
2020-02-29 21:07:51

Joe Guillemette
2020-02-29 21:23:33

Lorne Bixby
2020-02-29 21:26:16

Lorne Bixby
2020-02-29 21:26:50


原文網址 Lorne Bixby
2020-02-20 06:40:31

Why do all my large prints fail ? I've tried everything, hollowing, propper supporting, extra propper supporting, validator, clean fep, propper leveling with Flint read...

I get perfect small minis... Can't figure it out but i continue to end up with flat Stanley's in the tub and a perfect raft on the plate.

翻譯年糕

Fred Bey
2020-02-20 06:46:30

Lorne Bixby
2020-02-20 06:53:37

Stefan Giudici
2020-02-20 15:53:11

Lorne Bixby
2020-02-20 20:50:23

Chad Elstad
2020-02-21 13:00:17


原文網址 Lorne Bixby
2020-02-14 22:53:10

Is there a way to change the z rod default height when pausing a print ?

Mine pauses so low you can barely see what's on the plate...

翻譯年糕

Nipuna Gunarathne
2020-02-14 23:17:08

Lorne Bixby
2020-02-14 23:44:11


原文網址 Lorne Bixby
2020-02-13 21:41:28

Can anyone explain to me exactly what to click to download the resin exposure file from the photonster github page...

I don't understand github at all ?

翻譯年糕

Bill Connelly
2020-02-13 21:46:15

Falcon Tom
2020-02-13 21:46:53

Derek Reihe
2020-02-13 21:53:51

Sen Kun
2020-02-13 22:23:09

Lorne Bixby
2020-02-13 22:28:07

Lorne Bixby
2020-02-13 22:28:17


原文網址 Lorne Bixby
2020-02-01 06:29:27

Anyone else have Chitubox shut down when they support punched holes...
Like clockwork... Everytime

翻譯年糕

Richard Rush
2020-02-01 06:40:41


原文網址 Lorne Bixby
2020-01-22 20:40:10

Caught a print failing early on and I stopped the print. Pulled the vat and the LCD screen popped up with it... Now it's not sitting flush. Does it just drop in and push fit ?

翻譯年糕

Ryan Mitchell
2020-01-22 20:56:16

Lorne Bixby
2020-01-22 21:38:03


原文網址 Lorne Bixby
2020-01-17 20:34:47

Anyone have better support setting advice... Or a good video to watch, i get the islands... But even after that i keep waking up to supports holding nothing. It seems the suction is ripping them right off. I don't know if the contact points should be adjusted. Just small minis, shouldn't need to hollow.

翻譯年糕

Sander van Deijl
2020-01-17 20:57:24


原文網址 Lorne Bixby
2020-01-17 07:37:29

Help !
I just had a resin leak in my fep...
Changed everything cleaned up, got the baked resin off the lcd. Re-leveled and everything was working fine.

Now the touch screen is unresponsive...
Lit up but nothing is pressing.
And my plate is in the resin, i can't raise it.

翻譯年糕

Cobey Schmidt
2020-01-17 07:41:19

Ben Wood
2020-01-17 07:42:59

Lorne Bixby
2020-01-17 08:55:12

Lorne Bixby
2020-01-17 09:26:31


 

討論主題

全不選 常用關鍵字