Anycubic Photon Printer Owners 造訪社團 » 用戶發文

I need some help. I think I may have some resin in the ball joint of my build plate. I have the M2 and M3 hex keys that came with my printer. However, neither one of these hex keys fit the small screws. They are too large ? ... Anyone else experience this problem?

翻譯年糕

A big ‘thank you’ to this group!
I’m fairly new to 3D printing, bought my Photon S last November and I’m having fun printing 40k minis. Been learning through lots of trial and error. Went thru a 1Lt. bottle of AnyCubic Macaroon Blue ECO resin. Unfortunately, my models have all suffered from over exposure because I read some bad information regarding the ECO resin and settings. I was lead to believe that I should be using 12sec exposure times at 0.02mm layers. My mini models were losing details like crazy and I was getting frustrated because I knew it could be better.

This group is helping my understand this machine better and I greatly appreciate the collective knowledge that everyone is willing to share.

I’ve been experimenting more lately with the AmeraLabs SLA tests. I think I’m getting closer to a good balance with the details.

Number one lesson y’all taught me so far:
“The print exposure is too damn high.” Lol
So I made a meme for it lol

給這個社團的"謝謝"!
我相當新到3 d列印, 去年十一月買了我的光子s, 我很開心印刷40 k minis. 經歷了很多考驗和錯誤. 穿過1 lt. 一瓶任何cubic macaroon blue eco樹脂. 遺憾的是, 我的模特都因為我閱讀了一些關於生態樹脂和設定的壞資訊而遭受了影響. 我相信我應該在0.02 mm層使用12秒曝光時間. 我的迷你模特像瘋了一樣失去了細節, 我感到沮喪, 因為我知道它會更好.

這個小組幫助我更好地理解這台機器, 我非常感謝大家願意分享的集體知識.

最近我一直在嘗試ameralabs sla測試. 我想我越來越接近與細節的平衡.

到目前為止, 你們都教我的第一課:
"列印曝光太高了." lol
所以我為此做了一個meme lol

· 查看原文 · 為此翻譯評分

Anyone else still waiting on an order they made in December? Anyone else still waiting on an order they made in December? 翻譯年糕

Edit: Do you have experience with AnyCubic ECO macaroon blue resin?

I’ve been working with AnyCubic’s plant based blue resin on my Photon S. (Going to switch to grey) Been slicing with ChiTuBox.

I feel like I’m getting closer to the settings needed to produce high quality/definition minis, but I’m definitely not done yet.

I found a spreadsheet docs.google.com/…/1crvzMnt_8NJXAsABinoIhcOjE8l3h7s0L8…/edit…
This suggests I should be using 0.05mm layers, 12sec exposure with 5secs off, 70sec bottom exposure with 8 bottom layers.

I didn’t care for the results of those settings since I could see the layers and a lot of details were washed out.

I played with a number of settings and settled on this recently.

0.02mm layers height, 12 second exposure with 2 second delay, 70 second bottom exposure, 10 bottom layers

Had to reduce the delay so my print times weren’t so long. But I also discovered more support failures with the longer delay for some reason.

By the way, I’ve really only been at this about a month and I’ve had some good success but I want it to be even better. I also manually add supports to all of my prints, never use auto, and that increased my number of successful prints dramatically.

Note, my completed models required a lot of cleanup with an exacto blade to increase details. Each unit has at least 45mins under the blade and file.

Any suggestions that might help?

翻譯年糕