Anycubic Photon Printer Owners 造訪社團

原文網址 Mark Bryner
2019-10-29 14:52:01

Hi all.
I'm still having a really weird issue where my prints are being compressed to the build plate. Even with supports and a raft, the raft gets completely flattened.
Elegoo grey resin Bottom layers: 8 Bottom exposure: 100s Normal exposure: 18s Height: 0.05
So far, I've:
Leveled the build plate using both the paper method and Flint Read method Changed USB sticks Increased and decreased bottom exposure times by 10 seconds Made sure the FEB is clean and tight Printed at optimal room temperature
This issue just started to happen. Unfortunately, I can't figure out why. Some of you helped with providing advice, but I'm at a loss. Printing agaisnt the build plate without supports seems to be a no no for some, but I've been doing it for a while with no issues. When trying to switch to supports with rafts, the same issue persists.
Thanks for reading. 翻譯年糕

Péter Farsang
2019-10-29 15:14:42

Charles Rieken
2019-10-29 15:40:53

Jonathan Bollon
2019-10-29 19:49:44

Mark Bryner
2019-10-29 23:21:24

Mark Bryner
2019-10-29 23:21:40

Rikard Weijmer
2019-10-29 23:24:13

Mark Bryner
2019-10-29 23:36:26

Rikard Weijmer
2019-10-29 23:37:04

Mark Bryner
2019-10-29 23:52:02

Rikard Weijmer
2019-10-29 23:53:18

Charles Rieken
2019-10-30 00:00:26

Mark Bryner
2019-10-30 00:24:52

Mark Bryner
2019-10-30 00:25:41

Jonathan Bollon
2019-10-30 02:04:35

Mark Bryner
2019-10-30 03:43:16

Jonathan Bollon
2019-10-30 04:01:13

Mark Bryner
2019-10-30 05:30:10

Jonathan Bollon
2019-10-30 05:50:13

Mark Bryner
2019-10-30 05:53:08

Jonathan Bollon
2019-10-30 05:53:58

Péter Farsang
2019-10-30 15:30:09

Péter Farsang
2019-10-30 15:31:37

Mark Bryner
2019-10-30 16:36:10

Mark Bryner
2019-10-30 16:39:45

Mark Bryner
2019-10-30 16:39:56

Mark Bryner
2019-10-30 16:40:04

Mark Bryner
2019-10-30 16:40:39

Péter Farsang
2019-10-30 16:42:01

Jonathan Bollon
2019-10-30 19:22:41

Mark Bryner
2019-10-31 15:30:16

Ankh Thara
2019-10-31 15:36:46

Péter Farsang
2019-10-31 16:12:12

Mark Bryner
2019-11-01 00:40:18

Péter Farsang
2019-11-01 02:59:58

Mark Bryner
2019-11-01 15:54:34

Péter Farsang
2019-11-01 16:09:53

原文網址 Szabolcs Matefy
2019-10-29 14:10:43

Guys, what's the smallest key you met to assemble pieces? Apparently mine are too small (probably the hole shrank too much)...

翻譯年糕

Smith Hayward
2019-10-29 14:29:34

原文網址 Mariano Loisi
2019-10-29 13:49:46

Love this printer

喜歡這個印表機

· 查看原文 · 為此翻譯評分

Walter Policelli
2019-10-29 19:34:35

Mariano Loisi
2019-10-29 21:51:42

Walter Policelli
2019-10-30 19:38:12

Mariano Loisi
2019-10-31 01:40:41

原文網址 Yuzainis Saito
2019-10-29 13:44:42

Anyone used Esun standard grey resin before? Please share ur experience maybe based on successful rate, durability and detail. Thank you in advanced.

翻譯年糕

原文網址 Jason Glavich
2019-10-29 13:44:21

Man what a deal! 50 bucks + shipping

翻譯年糕

Ian Chess
2019-10-29 13:48:01

Jason Glavich
2019-10-29 13:48:48

Steven Huynh
2019-10-29 13:49:38

Chris Cowman
2019-10-29 13:49:59

Nathan Weeks
2019-10-29 13:55:50

Smith Hayward
2019-10-29 14:10:28

Danny Broekhuis
2019-10-29 14:11:03

Danny Broekhuis
2019-10-29 14:11:37

Danny Broekhuis
2019-10-29 14:12:17

Smith Hayward
2019-10-29 14:13:32

A.J. Dinsdale
2019-10-29 14:15:10

Danny Broekhuis
2019-10-29 14:23:58

A.J. Dinsdale
2019-10-29 15:15:31

César Fernández
2019-10-29 15:24:48

Danny Broekhuis
2019-10-29 16:36:47

Danny Broekhuis
2019-10-29 18:23:50

Danny Broekhuis
2019-10-29 19:00:28

Ioan Flerr
2019-10-29 20:42:50

Danny Broekhuis
2019-10-29 21:20:21

Danny Broekhuis
2019-10-29 21:22:01

Rose Stumpwater
2019-10-30 03:35:12

Jaco Norchie Nortje
2019-10-30 03:56:03

Charlie Anderson
2019-10-30 06:17:07

Jason Glavich
2019-10-30 06:35:49

Scott Roberts
2019-10-30 08:34:38

Ethan John Hainey
2019-10-30 14:01:38

Scott Roberts
2019-10-30 16:34:25

Colin Dewhurst
2019-10-30 19:17:07

Colin Dewhurst
2019-10-30 19:17:27

Danny Broekhuis
2019-11-01 00:25:11

原文網址 Evan Austin
2019-10-29 12:06:48

Hi everyone, new printer here. I was wondering if it is alright to have the photon printing inside a house? I'm wanting to set mine up in my guest room, but wanted to make sure it was safe. (Room has fan and an open window)

翻譯年糕

Smith Hayward
2019-10-29 12:10:34

Zach Chenoweth
2019-10-29 12:13:12

Stefan Giudici
2019-10-29 12:17:18

David Collinson
2019-10-29 21:00:58

原文網址 Jay Dubbs
2019-10-29 11:53:37

Is it safe to leave my photon printing all night while I sleep? I've heard of fdm ones causing fires and want to make sure that dsnt cross over to resin printers

翻譯年糕

Jay Kay
2019-10-29 11:54:34

Daniel Prows
2019-10-29 11:58:56

Cory Curtis Merrill
2019-10-29 12:19:57

Jay Dubbs
2019-10-29 12:38:59

Mark Anderson
2019-10-29 14:16:40

Stefan Giudici
2019-10-29 15:13:40

Janne Sjöström
2019-10-29 18:42:26

Evan Brand
2019-10-29 20:23:35

Neil Ramsay
2019-10-29 20:34:10

Jay Dubbs
2019-10-29 21:05:46

David Collinson
2019-10-29 21:08:36

Neil Ramsay
2019-10-29 21:10:27

Simon Wilson
2019-10-29 22:22:02

Jeff Greenfield
2019-10-30 00:17:49

Lee Johnson
2019-10-30 04:37:17

Mark Anderson
2019-10-30 04:39:30

原文網址 Ray Tan
2019-10-29 11:44:54

Have anyone tried replacing/modding the 405nm leds for 365nm ones?
I heard something abt LCD polarizer aggressively blocking certain spectrum of light.

翻譯年糕

Sen Kun
2019-10-29 12:07:25

原文網址 Oni Cron
2019-10-29 11:16:59

my crowfunding project ? ?

翻譯年糕

Charles Rieken
2019-10-29 15:35:53

Oni Cron
2019-10-29 22:46:33

Moritz Moe
2019-10-30 01:39:07

Oni Cron
2019-10-30 07:18:38

Robert Nisson
2019-11-01 12:13:13

Oni Cron
2019-11-07 21:58:35

Oni Cron
2019-11-07 21:59:27

原文網址 Kelly Anne
2019-10-29 11:16:27

Hi Everyone! I made a YouTube video about unboxing and setting up my Anycubic! It's my first YouTube video and I'm excited it was about such a cool printer :) Hope you enjoy it!