Anycubic Photon Printer Owners 造訪社團

原文網址 Dai Buckley Oam
2019-10-28 21:09:36

End result.

最終結果.

原文網址 Alessandro Tonin
2019-10-28 21:00:33

Hi, yesterday i just printed my first cube with my new anycubic. Here it's the result... I would say that is good but sometimes there are some mistakes, like a thin layer between the grid of the cube.. Do you know why this is happening?

翻譯年糕

Nathan Lange
2019-10-28 21:15:07

Christos Boukos
2019-10-28 21:15:14

Alessandro Tonin
2019-10-28 21:23:16

Emil Dziewanowski
2019-10-29 05:49:31

Alessandro Tonin
2019-10-29 08:04:54

Emil Dziewanowski
2019-10-29 08:08:13

Alessandro Tonin
2019-11-05 08:13:44

原文網址 Mike Tongue
2019-10-28 20:40:52

The books needed shelves and models .. here you go. Can anyone identify all 5 statues on the shelves ? Now on my Patreon : https://www.patreon.com/bigmrtong (don't forget all the books are free on Thingi https://www.thingiverse.com/thing:3942203 )

翻譯年糕

Rikard Weijmer
2019-10-28 21:40:38

Mike Tongue
2019-10-28 22:45:57

Christian Salling
2019-10-30 02:12:08

Mike Tongue
2019-10-30 02:17:36

原文網址 Dai Buckley Oam
2019-10-28 20:39:47

Test with the last of the black, clear, and a touch of the Monocure rapid flex was a complete success.

Giving it a few minutes in front of the lamp, and will check that out does have a little flex to it.

翻譯年糕

Danny Broekhuis
2019-10-28 20:50:32

Dai Buckley Oam
2019-10-28 20:51:23

Louis Siciliano
2019-10-30 05:15:36

Dai Buckley Oam
2019-10-30 06:30:27

原文網址 Phoenix Peng
2019-10-28 20:06:52

原文網址 Phoenix Peng
2019-10-28 20:04:02

Zachary Chin
2019-10-29 11:01:33

原文網址 Wee Liam Tai
2019-10-28 19:50:49

My resin print came out successfully. Base printed with fdm still wip

翻譯年糕

Neil Duffey
2019-10-29 05:11:07

原文網址 Dai Buckley Oam
2019-10-28 19:45:36

There's a lesson for you, kids.

After your calibration print, filter the vat for anything that might have come loose when it was under exposed.

Tsunami off the east structure!

翻譯年糕

Anton Ymer
2019-10-28 21:54:57

Tiernan Messmer
2019-10-28 22:53:12

Tiernan Messmer
2019-10-28 22:53:37

原文網址 Charlie Brett
2019-10-28 19:12:56

Lets talk toxicity. I know resin is not meant to be directly touched, tastes, or otherwise ingested. If I’m going to be watching the print, or in the same room/enclosure I need to be wearing a face mask with adequate ventilation. But what else? I’m planning on jumping in with both feet soon and my printer will most likely be located in my basement without direct ventilation access. If I enclose it in its own small room and wear a mask when in the room while it’s active, is that sufficient? Let’s assume this partition isn’t air tight, but it could be if I wanted.

翻譯年糕

Christopher Milnes
2019-10-28 19:19:25

Charlie Brett
2019-10-28 19:21:06

Christopher Milnes
2019-10-28 19:24:28

Thomas Kurtz III
2019-10-28 19:24:31

Neil Ramsay
2019-10-28 19:32:55

Dominick Trascritti
2019-10-28 19:36:04

Audrey Col
2019-10-28 19:53:42

Niall Forrester
2019-10-28 19:55:25

Joel Reid
2019-10-28 20:33:39

Joel Reid
2019-10-28 20:34:38

Audrey Col
2019-10-28 20:36:21

Evan Boone
2019-10-28 22:21:54

Charlie Brett
2019-10-28 22:26:47

Mike Roof
2019-10-28 22:47:20

David Collinson
2019-10-28 23:18:52

Kelly Wilkins
2019-10-28 23:29:20

Jim Lenglade
2019-10-28 23:41:24

Mike Roof
2019-10-28 23:47:57

Thomas Roe
2019-10-28 23:55:33

Francis X Benz
2019-10-28 23:59:31

Herman Simpson
2019-10-29 01:37:50

Herman Simpson
2019-10-29 01:41:20

Herman Simpson
2019-10-29 01:42:17

Smith Hayward
2019-10-29 15:13:13

Werner W Waage
2019-10-29 16:55:52

Christopher Milnes
2019-10-29 16:59:27

Werner W Waage
2019-10-29 17:02:52

Christopher Milnes
2019-10-29 17:04:53

Kelly Wilkins
2019-10-29 22:41:40

Audrey Col
2019-10-29 23:32:53

Kelly Wilkins
2019-10-29 23:35:49

Audrey Col
2019-10-29 23:37:15

原文網址 Jack Burton
2019-10-28 19:12:17

Just got a Photon S after running i3 Megas for about a year. Anycubic cube printed beautifully. I’m digging around on the FAQ and there’s a lot to learn. I recently saw a print that allows the build plate to be held at a 45 after print for drainage but I can’t find it now. Can anyone link it for me? What other upgrades and mods are worthwhile? I’m planning to print buttons for video game controllers and am experimenting with print orientation. It seems like the best workflow right now is Chitubox for positioning, support, and hollowing, then export as STL and slice in Anycubic as .pws. Hopefully Chitubox adds .pws support soon. Thanks!

翻譯年糕

Peter Csaki
2019-10-28 19:15:29