Anycubic Photon Printer Owners 造訪社團

原文網址 Ken Maxfield
2019-09-11 19:18:48

Hi, I have a question regarding hollowing out a model and the need for internal supports. Using Chitubox I have hollowed the model put a couple of holes in. Using auto supports it puts some support inside the hollowed model, plus I modify the external supports and add/remove as the model requires. Then I slice the model and run it through the Photon File Validator and fix what islands it can, but quite often it leaves islands that are inside the hollowed section and Chitubox doesn't let me create supports to fix these islands. Now most of the islands are only a pixel or 2 near the inside edge.

Is it fine to ignore the 2 or 3 internal islands it reports or is there any videos or help that help with supporting these islands inside the model?

Or alternatively is there a better way to hollow a model so these internal islands are not created?
Cheers

翻譯年糕

Peter Fulton
2019-09-11 19:27:15

Richard Shapiro
2019-09-11 21:48:25

原文網址 Phúc Nguyễn
2019-09-11 19:18:45

Luke Mason
2019-09-11 20:11:09

Phúc Nguyễn
2019-09-11 20:14:33

Adrian Walle
2019-09-12 04:13:08

Chris Thomas Bower
2019-09-12 09:08:11

Phúc Nguyễn
2019-09-12 09:54:18

Phúc Nguyễn
2019-09-12 09:58:26

Chris Thomas Bower
2019-09-12 11:03:34

原文網址 Cai Allin
2019-09-11 18:53:06

Hi all, so a print failed last night. I woke to see that it had stopped halfway through the print, the models were pressed against the FEP as if it was still printing.
So I went and clicked to move the build plate up but it made a sound as if the machine was stuck.
I turned it off and back on again and it was able to move again.
I have vent holes on each piece and all models are tilted. Any ideas what caused this?

Ps havent updated the firmware, could this be a problem?

翻譯年糕

David McGyver
2019-09-11 18:57:05

Cai Allin
2019-09-11 19:04:02

David McGyver
2019-09-11 19:26:54

Cai Allin
2019-09-11 22:15:14

Chamberlain Skeksil
2019-09-11 22:51:31

Henry Schaefer
2019-09-12 13:49:26

Cai Allin
2019-09-13 00:02:33

原文網址 Sam Vanroy
2019-09-11 18:52:32

First ever model I printed with Photon S (after the cube).
Sprayed it grey just to get a better idea of quality. Liking it.

Model from Artisan Guild
Standaard settings with provided Anycubic resin.

翻譯年糕

原文網址 Mika Egger
2019-09-11 18:44:01

It never fails to impress ?

翻譯年糕

原文網址 Amy Liao
2019-09-11 18:26:53

Super good news, especially for the Photonsters in Australia. The resin is re-available in eBay now, ships from AU warehouse with fast delivery,; black, white, skin, blue, red, orange, and green colors.

Do not miss that this time, order now. ? ?

? ? http://bit.ly/resin-ebay

The new released plan-based resin is also available. ?

? ? http://bit.ly/plantbasedresin

Any troubles, feel free to leave your comments below and PM. ❤️ ❤️

翻譯年糕

原文網址 Rafael Boisgontier
2019-09-11 18:26:43

Hello,

This is my first print. I am looking to make a matte black piece. I did not think that on such a thin thickness it would be transparent! I use Monocure 3D Black Resin https://www.monocure3d.com.au/Monocure-…/3dr-3587bk-500b.htm

My question is how to have a matte black in SLA?

翻譯年糕

Neil Ramsay
2019-09-11 18:49:44

Ofek Samsonov
2019-09-11 19:12:58

原文網址 Emre Güneş
2019-09-11 18:24:43

Is this screen used at photons

翻譯年糕

原文網址 Julia von Pfaler
2019-09-11 17:56:02

Got a permission to share the model with the group. Artisan Guild is asking for test prints, so if you'd like to add this awesome design into your collection, visit the Thingiverse link, but do share photos of the finished print for the designer ? Happy printing! Model: https://www.thingiverse.com/thing:3851318?fbclid=IwAR2AdLwzyq-Qno1kET2ZXzuMT4x0v__pS-r6JtbhYQHrmv3AKHxAIHEC7cg ----- And here's the link to their Patreon: https://www.patreon.com/ArtisanGuild ----- 翻譯年糕